782162
33
Zoom out
Zoom in
Previous page
1/48
Next page
33
NOUS VOUS CONSEILLONS DE:
• Graisser légèrement les segments de bascule de la
table, ainsi que le dispositif tendeur de ruban.
• Nettoyer la lame régulièrement: le bois laisse des
restes de résine.
• Contrôler régulièrement les doigts de guidage et les
roulements anti-pression. Si besoin est, régler, échan-
ger. Renouveler les pièces rapportées de table qui sont
usées.
• Maintenir toujours la surface supérieure de l’établi
exempte de résine.
RECOMMENDATIONS:
Slightly relubricate the slewing segments of the table and
the bend tensioning device.
• Regularly clean the saw band. Wood leaves resin sedi-
ments. We recommend the deresinifying concentrate
Pharmol HEK, item no. 61009700 for the cleaning.
• Regularly check the guiding rollers and the counter-
pressure bearings. If required, readjust or disassemble
them, and grease or exchange the parts.
• Exchange wornout table inserts.
• Ensure that the tabletop is always free of resin.
Aide au dépannage
Panne Cause possible Remède
Le moteur ne démarre pas a) pas de courant a) vérifier le fusible secteur
b) interrupteur, condensateur
défectueux b) électricien, vérifier
c) rallonge électrique défectueuse c) débrancher la fiche secteur, la
vérifier et la remplacer au besoin
Le ruban de scie gauchit a) guidage mal réglé a) régler le ruban de scie selon les
instructions de service
b) ruban de scie inadéquat b) sélectionner le ruban de scie selon
les instructions de service
Le ruban de scie se coince lors de
l’usinage a) ruban de scie émoussé a) remplacer le ruban de scie
b) ruban de scie inadéquat b) sélectionner le ruban de scie selon
les instructions de service
Le ruban de scie se coince lors de
l’usinage a) ruban de scie émoussé a) remplacer le ruban de scie
b) ruban de scie souillé de résine b) nettoyer le ruban de scie
c) guidage mal réglé c) régler le ruban de scie selon les
instructions de service
Trouble shooting
Problem Possible Cause Help
Saw blade gets loose after
turning off the motor Fastening
nut tightened
insufciently
Tighten fastening nut, M20 lefthanded thread
Motor does not start a) Fastening
nut tightened
insufciently
a) Check the mains fuse.
b) Extension cable
defect b) See „Electrical Connection“ in the operating manual
c) Connections on the
motor or switch defect c) Have it checked by an electrician
No motor output turns off
automatically Overload by
dull saw blade,
thermoprotection is
triggered
Insert a sharpened saw blade; motor can be turned on again
after the cooling period
Burns on the cutting surface c) with longitudinal
cuts c) Exchange the longitudinal stop
d) with cross cuts d) Align the slide carriage with the saw blade
a) Fastening
nut tightened
insufciently
a) Tighten fastening nut, M20 lefthanded thread
b) Wrong saw blade b) Insert saw blade with 20 or 28 teeth for longitudinal cuts
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SB08 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SB08 Woodster in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info