782162

Scheppach SB08 Woodster Manual

25
Zoom out
Zoom in
Previous page
1/48
Next page
25
contraire des aiguilles d’une montre lorsque la lame
de scie tourne dans le sens contraire de la face
arrière de la scie.
3 Serrer l’écrou de rétention (K).
ALIGNER LE GUIDE-LAME SUPÉRIEUR
Le guide-lame supérieur se compose de :
• un palier de butée (assure le support arrière de la
lame de scie) et
• deux doigts de guidage (assurent le support latéral).
Il convient d’ajuster le palier et les doigts de réglage
après chaque remplacement de ruban ou de bande.
Attention :
Vérifier régulièrement les paliers afin de détecter toute
trace d’usure. Si nécessaire, remplacer simultanément
les deux paliers de guidage.
RÉGLAGE DU PALIER DE BUTÉE FIG. 9
Si nécessaire, aligner la lame de scie à ruban et la ten-
dre.
1 Desserrer la vis de serrage du palier de butée (50).
2 Régler la position du palier de butée. (51) (Écart
entre palier et lame de scie à ruban = 0,5 mm). Si la
lame de scie à ruban est tournée à la main, s’assurer
qu’elle ne touche pas le palier.
3 Serrer la vis de serrage du palier de butée (50).
RÉGLAGE DES DOIGTS DE GUIDAGE FIG. 10
1 Desserrer les vis (52).
2 Presser les doigts de serrage (53) l’un contre l’autre
(contre la lame de scie à ruban).
3 Faire tourner la lame de scie à ruban à plusieurs
reprises dans le sens des aiguilles d’une montre pour
guider les doigts de serrage dans la bonne position –
les deux doigts de serrage doivent légèrement toucher
la lame de scie à ruban.
4 Serrer de nouveau les vis (52).
ALIGNER LE GUIDE-LAME INFÉRIEUR
Le guide-lame inférieur se compose de :
• un palier de butée (assure le support arrière de la
lame de scie) et
• deux doigts de guidage (assurent le support latéral).
Il convient d’ajuster le palier et les doigts de réglage
après chaque remplacement de ruban ou de bande.
Attention :
Vérifier régulièrement les paliers afin de détecter toute
trace d’usure. Si nécessaire, remplacer simultanément
les deux paliers de guidage.
ALIGNMENT OF THE UPPER BAND GUIDE
The upper band guide consists of:
• a compression bearing (supports the sawing band from
the back side) and
• two guiding pins (giving additional lateral support).
Bearing and guiding pins must be readjusted after each
band or track replacement.
Attention:
Check all bearings for wear on a regular basis. If neces-
sary replace both guide bearings at the same time.
COMPRESSION BEARING SETTING FIG. 9
If necessary align the sawing band and tighten it.
1 Release the compression bearing adjustment screw
(50).
2 Set the compression bearing position. (51) (Distance
between bearing and sawing band = 0.5 mm). If the
sawing band is turned by hand it must not touch the
bearing.
3 Tighten the compression bearing adjustment screw
(50).
SETTINGS OF THE GUIDING PINS FIG. 10
1 Release the screws (52).
2 Press the guiding pins (53) together (against the saw-
ing band).
3 Turn the sawing band clockwise by hand several times
in order to bring the guiding pins in the correct po-
sition - both pins should slightly touch the sawing
band.
4 Tighten the screws again (52).
ALIGNMENT OF THE LOWER SAWING BAND GUIDE
The lower sawing band guide consists of:
• a compression bearing (supports the sawing band from
the back side) and
• two guiding pins (giving additional lateral support).
Bearing and guiding pins must be readjusted after each
band or track replacement.
Attention:
Check all bearings for wear on a regular basis. If neces-
sary replace both guide bearings at the same time.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SB08 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SB08 Woodster in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info