782162

Scheppach SB08 Woodster Manual

21
Zoom out
Zoom in
Previous page
1/48
Next page
21
RÉGLAGE DU PLATEAU DE TABLE FIG. 4
1 Régler le plateau de table à la position zéro et bien
serrer la vis à ailettes (E) et le levier de serrage (F).
2 Aligner le plateau de table parallèlement à la lame de
scie et bien serrer les 3 vis. S’assurer que la lame de
scie est bien centrée dans l’insert de table.
RÉGLER LE PLATEAU DE TABLE
PERPENDICULAIREMENT À LA LAME DE SCIE FIG. 5
1 Régler le guide-lame supérieur vers le haut et le
fixer.
2 Desserrer le levier de serrage (F) et la vis à ailettes
(E) sur le segment à bascule (G).
3 Aligner le plateau de table perpendiculairement (9-
5°) à la lame de scie (utiliser une équerre).
4 Ajuster à l’aide de la vis de fixation (H) et fixer avec
un écrou Fig. 4
MONTAGE DE LA BUTÉE LONGITUDINALE FIG. 6
La butée longitudinale (5) peut être utilisée sur les deux
faces de la lame de scie.
La fixation se fait des deux côtés de la table avec une
bride de serrage (J)
MONTAGE DU SUPPORT DE POUSSOIR
Visser le boulon à crochet du poussoir dans le filetage
supérieur du cadre de scie et le fixer avec un écrou.
Dans le cas où le poussoir n’est pas utilisé, l’accrocher
sur le boulon à crochet.
m Mise en service
Respecter les consignes de sécurité avant de faire la mise
en service.
Tout les dispositifs de sécurité et de protection doivent
être montés pour le travail.
REMPLACER LA LAME DE SCIE À RUBAN
Danger !
Risque de blessures même si la scie à ruban est arrêtée.
Porter des gants de protection pour remplacer la lame de
scie à ruban.
N’utiliser que des lames de scie à ruban appropriées
1 Desserrer les 2 vis à tête moletée (D) et retirer la
pièce de renforcement en forme d’U (C) en dessous
de la table de scie (Fig. 3)
2 Ouvrir les deux portes du boîtier.
ADJUSTING THE TABLE TOP FIG. 4
1 Set the table top to home position and tighten the
wing bolt (E) and the clamp lever (F) firmly.
2 Align the table top parallel to the sawing blade and
tighten the 3 screws. Observe that the sawing blade
is centred in the table inlay.
ADJUSTING THE TABLE TOP
AT THE RIGHT ANGLE TO THE SAWING BLADE FIG.5
1 Fully set the belt guide upwards and clamp it tight.
2 Release the clamping lever (F) and the wing bolt (E)
at the swivelling segment (G).
3 Align the table at the right angle (9-5°) to the sawing
blade (use back square).
4 Adjust the adjusting screw (H) and lock it with a nut
Fig. 4
INSERTING THE LONGITUDINAL ARRESTER FIG. 6
The longitudinal arrester (5) can be used on both sides of
the sawing blade.
Clamping is done on both sides of the table with the bolt
lever (J)
MOUNTING THE SLIDING ROD HOLDER
Screw the hook screw for the sliding rod into the thread
at upper frame and lock it with the nut.
If the sliding rod is not in use, hang it on the hook screw.
m Commissioning
Before putting the machine into operation, carefully observe
the safety instructions.
When working with the machine, all protective devices
and guards must be fitted.
REPLACEMENT OF THE SAWING BAND
Danger!
Danger of injury even with sawing band at standstill.
When replacing the sawing blade, wear gloves.
Only use suitable sawing blades
1 Release the 2 knurl screws (D) and remove the U
bracing (C) under the sawing table (Fig.3 )
2 Open both housing doors.
3 Fold away the lower sawing band protection (K).
Fig.7
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SB08 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SB08 Woodster in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info