Manual Scheppach RS400 (page 20 of 160) (All languages)

781416

Zoom out

Zoom in

1/160

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

20 | GB

Roller sieve, frame arms, Fig. 1

Attach the frame arms (2) to the pre-assembled roller

sieve (1).

2 spacer pins (a)

4 serrated lock washers ø8,2 (b)

4 hexagon nuts M 8 (c)

1 hexagon bolt M10x70 (d)

1 small washer ø10 (e)

1 hexagon nut M10 (f)

Frame struts, frame wall, Fig. 2

Assemble frame struts (4) and frame wall (7).

6 hexagon bolts M8 x 65 (g)

6 washers ø8 (h)

6 serrated lock washers ø8,2 (b)

6 hexagon nuts M8 (c)

Mind the correct diagonal-cut strut position.

Supporting legs, Fig. 3

Attach the supporting legs (8) to the frame struts (4).

2 hexagon bolts each M8x45 (i)

2 serrated lock washers each ø8,2 (b)

2 hexagon nuts each M8 (c)

Wheels, Fig. 4

Fit the wheels (9) to the frame struts (4).

1 cheese-head screw each M10x95 (j)

1 washer each ø10 (e)

1 bush each (k)

2 hexagon nuts each M10 (f)

When reversing and tightening the hexagon nuts,

make sure the wheels turn easily.

Fit the lower bolts into the frame wall (7).

2 hexagon bolts M8 x 65 (g)

2 washers ø8 (h)

2 serrated lock washers ø8,2 (b)

2 hexagon nuts M8 (c)

Frame arms, frame struts, Fig. 5

Bolt together frame arms (2+3), frame struts (4), gus-

set plates (5+6) and the transport bow (11) .

6 hexagon bolts M8x65 (g)

8 serrated lock washers ø8,2 (b)

6 hexagon nuts M8 (c)

2 hexagon bolts M8 x 70 (l)

Fasten the gusset plate with the cable clamp (5) at

the front right side.

Sieve drum insert

The drum remains attached to the frame.

Remove the drum bars tted to the drum inside in

longitudinal direction. For the following remounting,

mark the position of the drum bars with a felt pen.

Fig. 6

Place the sieve insert (10) into the sieve drum in such

a way that the sieve edge is covered by a drum bar.

Push the rings at front and back into the sieve drum

and put them into a vertical position in the drum.

Fig. 7

Bolt the rings through the sieve mashes.

3 Allen screws each M6x16 (m)

3 washers each ø6 (n)

3 serrated lock washers each A8,3 (o)

3 hexagon nuts each M6 (p)

Continue mounting both drum bars at the points ear-

lier marked with a felt pen.

10. Putting into operation

m ATTENTION!

Always make sure the device is fully assembled

before start-up!

Filling with material Fig. 8

Soil is always lled into the drum from the front.

• Before putting the implement into operation, ob-

serve the safety instructions.

• All guards and safety devices must be tted.

• After connection to the electrical power, your

RS400 is ready for service.

• Always attach the power cable to the clamp in the

gusset plate.

Setting up, Fig. 9

Depending on the place of setting up, incline the sieve

drum as required. Displace the hexagon bolt (arrow).

The degree of inclination depends on the type of soil

to be sieved.

For loose material we recommend more inclination,

and for solid material less inclination.

Angle positioning large - faster throughput - top hole

Angle positioning small - slower throughput - bottom

hole

Electrical connection

The installed electrical motor is connected and ready

for use. The connection meets the corresponding

VDE and DIN regulations.

The power connection on the part of the client, as

well as the extension cables used, must meet these

regulations.

Faulty power supply cables

Insulation damage often occurs at power supply ca-

bles.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach RS400 in the language / languages: All languages as an attachment in your email.

The manual is 6.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach RS400

Scheppach RS400 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach RS400 Manual

Product: