781416
21
Zoom out
Zoom in
Previous page
1/160
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 21
Causes are:
Pressure points when power supply cables are
routed through the window or door gaps.
Bends due to improper fastening or guiding of the
power supply cables.
Interfaces by running over the power supply cables.
Insulation damage by pulling off the wall outlet.
Cracks due to ageing of the insulation
Such defective power supply cables must not be used
and are extremely dangerous to life because of the
insulation damage!
Check power supply cables regularly for damage.
Make sure that the power cable is not connected to
the mains supply when you check.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking H 07 RN.
The printing of the type designation on the connec-
tion cable is mandatory.
Single-phase motor
Line voltage must be 230 V 50 Hz.
Extension cables up to 25 m in length must have a
minimum cross section of 1.5 mm2, above 25 m at
least 2.5 mm2.
The power supply is protected by a timed fuse of 16 A.
Electrical connection and repair work may be carried
out by a qualied electrician only.
Please specify the following with all inquiries:
Motor manufacturer
Motor current type
Specications on machine nameplate
Specications on switch nameplate
When sending in the motor, always include the com-
plete drive unit with switch.
11. Cleaning
m WARNING
Conduct maintenance and cleaning works only with
the unit shut off and the power supply plug pulled.
Drum cleaning
Take off soil from the drum after every use. The run-
ning surface of the vee-belt on the drum must always
be kept clean. Soil and stones ruin the vee-belt.
12. Transport
m WARNING
Only transport with the motor switched off and the
mains plug unplugged.
Ensure that the load is well secured when transport-
ing the machine in a motor vehicle.
Changes in position
Tilt the machine on the wheels. The machine can now
be driven on the wheels.
13. Storage
Store the machine in a clean, dry, frost-free area,
out of reach of unauthorised persons.
Cover the machine with a breathable material.
Airtight materials lead to condensate forming and
cause corrosion.
Keep the machine in good condition. If necessary,
replace the safety and instruction signs.
14. Maintenance
m WARNUNG
Conduct maintenance and cleaning works only with
the unit shut off and the power supply plug pulled.
If needed, re-adjust the brush bar on the roller sieve.
Drive belt tensioning, Fig. 10
Remove the cover.
Re-adjust the at belt tensioning by releasing 3 hexa-
gon bolts M6 (r) and pulling the motor upwards.
Retighten the bolts.
Drum vee-belt tensioning, Fig. 11
Release the hexagon nut M 10 and re-adjust the
bearing correspondingly. Retighten the hexagon nut.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: driving belts, sieve insert, slat, mat
* Not necessarily included in the scope of delivery!
15. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach RS400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach RS400 in the language / languages: All languages as an attachment in your email.

The manual is 6.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach RS400

Scheppach RS400 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info