782076

Scheppach PT85 Woodster Manual

23
Zoom out
Zoom in
Previous page
1/156
Next page
23
Cutter block guard (Fig. 10.1/10.2)
Height adjustment is done with the star grip J screw fitted
to the left side of the machine. After releasing the star
grip screw K, the cutter block guard can be moved to the
side and the correct planing width set. Press the guard
down again to fix it in the right position, and tighten the
handles.
Surfacing:
The amount of chip removal is set by means L of the scale
M on the front side of the table top M. The best surface is
obtained at a planing depth between 0.5 and 1.5 mm.
Warning:
The part of the cutter block not used must by covered
by the guard. Working position is in front of the machine
at the side of the infeed table. Put the fingers of both
hands on top of the work piece. Do not hold the work
piece edges.
The work pieces to be planed must lie firmly on the table
so they can be guided safely. For short work pieces use a
feed stick.
Thicknessing:
• Following the scale and using the handle O on the spin-
dle, set the thicknessing table to the desired height. 1
rotation = 3 mm.
• Narrow wood is introduced in the centre.
• When thicknessing, the table must be treated with oil
at regular intervals. After a long period of use, or when
planing humid wood, it can happen that the work piece
is not further pulled in.
Warning:
In case of a defect, switch off the machine at once. Do
not remove any chips or splinters from the tables while
the machine is running. Work pieces below 250 mm may
not be planed.
Changing the knives (Fig. 11)
• Put the main switch of the machine to OFF position.
• Pull the power supply plug from the socket.
• Block the cutter block guard in the lifted position.
• Release and remove the four knife clamping screws.
• Lift the knives and knife support from the cutter block.
• Remove the chips and any resin from the cutter block
and knife support.
• Place new knives into the cutter block and fix them with
the rectangle slots in both screw heads. (With these two
screws, height-adjustment of the knife is done.)
• Place the knife support onto the knife.
• Slightly tighten the four clamping bolts.
• Repeat these actions for the second knife.
• Then adjust the planer/thicknesser knives exactly with
the output table. Use a ruler that you put onto the out-
put table.
• By the two set screws, the knife can be adjusted for
height.
• By turning the cutter block and using the ruler, you can
see the height adjustment.
• The knife is exactly set, when the ruler is moved by the
knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
Protection de l’arbre de rabotage (Fig. 10.1/10.2)
Le réglage en hauteur s’effectue par la vis poignée-étoile
J monté à gauche de la machine. En relâchant cette vis K,
le protecteur des couteaux peut être poussé à côté, pour
régler la largeur de rabotage correcte. Presser le protec-
teur à nouveau vers le bas pour le fixer dans la position
correcte, et serrer les poignées.
Dégauchisser:
La profondeur de rabotage est réglée par la poignée L
monté sur la face de la table N, à l’aide d’une échelle.
La meilleure M surface s’obtient avec une profondeur de
rabotage entre 0,5 et 1,5 mm.
Attention:
Le dispositif de protection de l’arbre de rabotage doit
recouvrir la partie non utilisée de l’arbre. La position
de travaille est devant la machine à côté d’alimen-
tation de bois. Mettre les doigts de deux mains sur la
pièce à travailler. Ne pas toucher les arêtes du bois.
Seulement traiter des pièces de bois reposant fermément
sur la table et pouvant être guidées de manière sûre. Pour
le dégauchissage de pièces courtes, utiliser un guide
d’avance pour pièce courte.
Raboter:
• Régler la table de rabotage à la hauteur désirée à l’aide
de la poignée O sur la broche, et l’échelle. 1 révolution
= 3 mm.
• Introduiser les pièces de bois étroites au centre.
• Lors du rabotage, la table doit être huilée régulièrement.
Après une période d’usage prolongée, ou en traitant le
bois humide, l’avance du bois peut être bloquée.
Avertissement:
En cas d’une panne, mettre la machine hors service im-
médiatement. Ne pas enlever des copeaux pendant que
la machine est en marche. Il est interdit de raboter des
pièces de bois d’une dimension inférieure à 25 cm.
Remplacement des fers de rabot (Fig. 11)
• Mettre l'interrupteur à la position «Arrêt».
• Débrancher la prise d’alimentation.
• Bloquer la protection de l'arbre de rabotage dans sa po-
sition la plus haute.
• Relâcher et enlever les 4 vis de serrage de lame.
• Enlever la lame et le support de l'arbre.
• Enlever copeaux et résine de l’arbre et du support.
• Mettre la nouvelle lame dans l'arbre et la fixer par les
fentes dans les 2 têtes de vis. (Ces 2 vis servent à régler
en hauteur la lame.)
• Mettre le support de lame sur la lame.
• Serrer légèrement les 4 vis de serrage.
• Répéter la procédure pour la deuxième lame.
• Ensuite, régler précisement la hauteur des lames en re-
lation à la table d’enlèvement, en utilisant une règle.
• La hauteur des lames est réglées par les deux vis de
réglage.
• Vérifier la hauteur des lames en tournant l’arbre, tout en
maintenant la règle sur place.
• La lame a la position correcte si la règle est avancée par
les lames pas plus de 3 mm.
• Ensuite, reserrer toutes les vis fermément (8,4 N/m).
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT85 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT85 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info