782076
25
Zoom out
Zoom in
Previous page
1/156
Next page
25
must be tightened (8.4 N/m).
Please mind:
Sharp planer/thicknesser knives guarantee a clean plan-
ing surface and put less stress on the motor.
After three grinding actions, a maximum material re-
moval of 3 x 0.05 mm may not be exceeded.
The planer/thicknesser blades used on this machine are
not suitable for rebating and dovetailing.
Finally lower the cutter block guard again onto the ta-
ble. Cover the cutter block and block it with the star grip
screw.
Installation
Make sure there is sufficient space for handling the
work piece over the whole length without the operator
(or another person) having to stand in line with the work
piece.
Using bolts, washers and hexagon nuts (not supplied
with the machine), the planer/thicknesser can be bolted
to a work bench.
The planing machine must be bolted onto a firm, level
surface.
The machine may not tilt, and the table must be
aligned.
Machine setting up and functions
The electric planer/thicknesser is transportable. It is pow-
ered by a single-phase motor and is double insulated. It
has been designed for planing wood, and it features a ra-
tional construction, easy operation, and high efficiency.
Maintenance
Always pull the power supply plug before doing any servic-
ing work. Having finished the work, put the cutter block
guard in operating position again.
Machine care
The planer/thicknesser requires little maintenance. The
ball bearings are permanently lubricated. After approx.
ten operating hours, lubrication of the following parts is
recommended:
Bearing of the infeed and output roller
Bearing of pulley and sprocket
The threaded spindle for height-adjustment of the thick-
nessing table may only be treated with a dry lubricant
agent.
The table surfaces as well as the infeed and output rollers
must always be kept free from resin.
Faire attention:
Ne travaillez qu'avec des lames bien affûtées. Elles dé-
chargent le moteur et garantissent une surface lisse.
Après avoir affûté les lames trois fois, l’enlèvement de
matériel ne doit pas excéder 3 x 0,05 mm.
Les lames usées sur cette machine ne sont pas appro-
priées à entailler en queue d’aronde.
Finalement abaisser la protection de l'arbre de rabotage
sur la table, couvrir l'arbre et le serrer avec la vis poi-
gnée-étoile.
Installation
Vérifier qu’il y ait de la place suffisante pour guider le
bois sur toute sa longueur, sans quune personne doit se
trouver dans une ligne avec la pièce à travailler.
La rabo-dégau peut être fixée sur un établi à l’aide de
boulons, rondelles et écrous hexagonaux (non livrés).
La rabo-dégau doit être vissée fermément à une surface
solide et lisse.
La machine ne doit pas basculer, et les tables doivent
s'aligner.
Construction et fonctions de la machine
La rabo-dégau peut être transportée. Elle est actionnée
par un moteur monophasé et a une isolation double. Elle
a été conçue pour travailler le bois. Sa construction est
rationnelle et de haute efficacité, et elle est facilement
maniable.
Entretien
Lors de toute opération d’entretien et de nettoyage, arrê-
ter le moteur et débrancher la prise d’alimentation. Une
fois les travaux achevés, tous les dispositifs de protection
doivent être remontés immédiatement.
Entretien de la machine:
La rabo-dégau exige peu d’entretien. Les paliers sont
graissés à vie. Après 10 heures de service, il est recom-
mandé de huiler les paliers suivants:
Paliers des rouleaux d'avance et de sortie
Paliers de la poulie et de la roue dentée
La broche filetée pour le réglage en hauteur de la table de
rabotage doit uniquement être traitée avec un lubrifiant
sec.
Il faut veiller à ce que toutes les tables et tous les rouleaux
ne présentent aucune trace de résine.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT85 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT85 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info