782078
25
Zoom out
Zoom in
Previous page
1/116
Next page
25
grip screw.
Installation
Make sure there is sufficient space for handling the •
work piece over the whole length without the operator
(or another person) having to stand in line with the
work piece.
Using bolts, washers and hexagon nuts (not supplied •
with the machine), the planer/thicknesser can be
bolted to a work bench.
The planing machine must be bolted onto a firm, level •
surface.
The machine may not tilt, and the table must be •
aligned.
Machine setting up and functions
The electric planer/thicknesser is transportable. It is
powered by a single-phase motor and is double insu-
lated. It has been designed for planing wood, and it fea-
tures a rational construction, easy operation, and high
efciency.
Maintenance
Always pull the power supply plug before doing any serv-
icing work. Having finished the work, put the cutter block
guard in operating position again.
Machine care
The planer/thicknesser requires little maintenance. The
ball bearings are permanently lubricated. After approx.
ten operating hours, lubrication of the following parts is
r e c o m m e n d e d :
Bearing of the infeed and output roller•
Bearing of pulley and sprocket•
Greasing the chain. •
The threaded spindle for height-adjustment of the thick-
nessing table may only be treated with a dry lubricant
agent.
The table surfaces as well as the infeed and output rollers
must always be kept free from resin.
Regularly clean infeed and output rollers. •
In order to avoid overheating of the motor, regularly •
check the air openings for any dust sticking on.
After a longer period of use, it is recommended to •
have the machine checked by an authorized dealer
service.
Tool care:
Cutter block, clamping devices, knife supports and •
knives must be regularly cleaned from resin, as a clean
tool improves the planing quality. To this purpose,
clamping devices, knife supports and knives can be
put in a common resin remover for 24 hours.
Installation
Vérifier qu’il y ait de la place suffisante pour guider le •
bois sur toute sa longueur, sans qu’une personne doit
se trouver dans une ligne avec la pièce à travailler.
La rabo-dégau peut être fixée sur un établi à l’aide de •
boulons, rondelles et écrous hexagonaux (non livrés).
La rabo-dégau doit être vissée fermément à une surface •
solide et lisse.
La machine ne doit pas basculer, et les tables doivent •
s'aligner.
Construction et fonctions de la machine
La rabo-dégau peut être transportée. Elle est actionnée
par un moteur monophasé et a une isolation double. Elle
a été conçue pour travailler le bois. Sa construction est
rationnelle et de haute efficacité, et elle est facilement
maniable.
Entretien
Lors de toute opération dentretien et de nettoyage, arrê-
ter le moteur et débrancher la prise dalimentation. Une
fois les travaux achevés, tous les dispositifs de protection
doivent être remontés immédiatement.
Entretien de la machine:
La rabo-dégau exige peu d’entretien. Les paliers sont
graissés à vie. Après 10 heures de service, il est recom-
mandé de huiler les paliers suivants:
Paliers des rouleaux d'avance et de sortie•
Paliers de la poulie et de la roue dentée•
Graissage de la chaîne. •
La broche filetée pour le réglage en hauteur de la table
de rabotage doit uniquement être traitée avec un lubri-
fiant sec.
Il faut veiller à ce que toutes les tables et tous les rou-
leaux ne présentent aucune trace de résine.
Des rouleaux sales doivent être nettoyés.
Pour éviter l’échauffement du moteur, contrôler régulière-
ment si les ouvertures d’air sont libres de poussière.
Aps une utilisation prolongée, il est recommandé de
faire inspectionner la machine par un service d’entretien
age.
Entretien des outils:
Enlever régulièrement la résine de l’arbre de rabotage,
des dispositifs de serrage, des supports de lames et des
lames. Un outil net améliore la qualide coupe. Pour
enlever la résine, les outils peuvent être immersés dans
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT 106 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT 106 Woodster in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info