782078

Scheppach PT 106 Woodster Manual

23
Zoom out
Zoom in
Previous page
1/116
Next page
23
piece edges.
The work pieces to be planed must lie firmly on the table
so they can be guided safely. For shorter work pieces use
a feeding tube or the guide handle.
Thicknessing:
Following the scale and using the handle• (O) on the
spindle, set the thicknessing table to the desired
height. 1 rotation = 3 mm.
Slide narrow wood to the centre of the thickness •
table.
For thickness planing and also jointing the use of spray
lubrication or compound. After a long period of use, or
when planing humid wood, it can happen that the work
piece is not further pulled in.
Warning:
In case of a defect, switch off the machine at once.
Do not remove any chips or splinters from the tables
while the machine is running. Work pieces below 250
mm length may not be planed.
Changing the knives (Fig. 11)
Put the main switch of the machine to OFF position. •
Pull the power supply plug from the socket.•
Block the cutter block guard in the lifted position.•
Release and remove the four knife clamping screws.•
Lift the knives and knife support from the cutter •
block.
Remove the chips and any resin from the cutter block •
and knife support.
Place new knives into the cutter block and fix them •
with the rectangle slots in both screw heads. (With
these two screws, height-adjustment of the knife is
done.)
Place the knife support onto the knife. •
Slightly tighten the four clamping bolts.•
Repeat these actions for the second knife.•
Then adjust the planer/thicknesser knives exactly with •
the output table. Use a ruler that you put onto the
output table.
By the two set screws, the knife can be adjusted for •
height.
By turning the cutter block and using the ruler, you •
can see the height adjustment.
The knife is exactly set, when the ruler is moved by the •
knives not higher than 3 mm.
After a successful knife setting, all clamping screws •
must be tightened (8.4 N/m).
Please mind:
Sharp planer/thicknesser knives guarantee a clean •
planing surface and put less stress on the motor.
Observe all knifes to have the same width (unbalance), •
when finish-grinding. The minimum width of the knifes
is 20mm.
The planer/thicknesser blades used on this machine •
are not suitable for rebating and dovetailing.
Finally lower the cutter block guard again onto the •
table. Cover the cutter block and block it with the star
pièce à travailler. Ne pas toucher les arêtes du bois.
Seulement traiter des pièces de bois reposant fermé-
ment sur la table et pouvant être guidées de manière
sûre. Pour des pièces à usiner courtes, utiliser un tiroir
d’alimentation ou la poignée de guidage.
Raboter:
Régler la table de rabotage à la hauteur désirée à •
l’aide de la poignée (O) sur la broche, et l’échelle. 1
révolution = 3 mm.
Introduire du bois étroit au centre de la table de •
rabotage.
Pour le rabotage d’épaisseur comme pour le dressage il
est recommandé d’utiliser un spray de glissement ou une
pâte. Après une période d’usage prolongée, ou en traitant
le bois humide, l’avance du bois peut être bloquée.
Avertissement:
En cas d’une panne, mettre la machine hors service im-
médiatement. Ne pas enlever des copeaux pendant que
la machine est en marche. Il est interdit de raboter des
pièces de bois d’une dimension inférieure à 25 cm.
Remplacement des fers de rabot (Fig. 11)
Mettre l'interrupteur à la position «Arrêt».•
Débrancher la prise d’alimentation.•
Bloquer la protection de l'arbre de rabotage dans sa •
position la plus haute.
Relâcher et enlever les 4 vis de serrage de lame.•
Enlever la lame et le support de l'arbre.•
Enlever copeaux et résine de l’arbre et du support.•
Mettre la nouvelle lame dans l'arbre et la fixer par les •
fentes dans les 2 têtes de vis. (Ces 2 vis servent à
régler en hauteur la lame.)
Mettre le support de lame sur la lame.•
Serrer légèrement les 4 vis de serrage.•
Répéter la procédure pour la deuxième lame.•
Ensuite, régler précisement la hauteur des lames •
en relation à la table d’enlèvement, en utilisant une
règle.
La hauteur des lames est réglées par les deux vis de •
réglage.
Vérifier la hauteur des lames en tournant l’arbre, tout •
en maintenant la règle sur place.
La lame a la position correcte si la règle est avancée •
par les lames pas plus de 3 mm.
Ensuite, reserrer toutes les vis fermément (8,4 N/m). •
Faire attention:
Ne travaillez qu'avec des lames bien affûtées. Elles •
déchargent le moteur et garantissent une surface
lisse.
Lors du repassage, veiller à ce que toutes les lames •
aient la même largeur (charge déséquilibrée). La
largeur minimale des lames est de 20 mm.
Les lames usées sur cette machine ne sont pas •
appropriées à entailler en queue d’aronde.
Finalement abaisser la protection de l'arbre de •
rabotage sur la table, couvrir l'arbre et le serrer avec
la vis poignée-étoile.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT 106 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT 106 Woodster in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info