782078

Scheppach PT 106 Woodster Manual

19
Zoom out
Zoom in
Previous page
1/116
Next page
19
Unpacking the machine
Check the contents of any possible transport damage.
In case of a damage, inform immediately the forwarding
agent. Check the contents for completeness. Inform im-
mediately the dealer in case of any missing parts.
The complete machine is shipped in one single carton
box. Any additional parts that have to be attached to
the machine, must be identified before starting the as-
sembly.
Fig. 2
1 Planing and thicknessing machine
2 Ripping fence
3 Handle
4 Suction connector
Assembly
Assembling trimming endstop unit Fig. 3
Attention! Device must be unplugged from mains during
any retooling or assembly work
Mount the trimming bracket (A) on the side wall of the
planing machine with 2 semicircular allen screws (B) M6
x20 mm and 2 washers 6 mm (B). Now slide grooved stop
rail (C) in the pre-assembled nuts and tighten them with
the 4 wing screws (E).
Justifying the trimming endstop Fig. 3
Postion the endstop at a 90 ° angle, and clamp it in
place with the toggle screw (H). Now place the cross-
slotted screw (F) against the endstop and secure it with
the nut. Then position the endstop at 45° and clamp it
in place with the clamping screw (H). Next, place the
allen screw (G) against the endstop and secure it with
the nut.
Now check both brackets with a sample and re-justify
the scale if required.
Assembling planer axle guard Fig. 5, 6
The knurled screw (6) is for raising the planer axle guard
(1).
Déballage de la machine
Vérifier dès la livraison, qu’aucune pièce n’ait été dé-
tériorée pendant le transport. En cas de réclamation,
informer aussitôt le livreur. Vérifier que la livraison soit
bien complète. En cas de réclamation, informer aussitôt
le vendeur.
La machine est expédiée dans un seul carton. Des acces-
soires supplémentaires doivent être localisés et identifiés
avant le début du montage.
Fig. 2
1. Raboteuse-dégauchisseuse
2. Butée de rabotage
3. Poignée
4. Manchon de prise d’air
Montage
Montage butée de dressage Fig. 3
Attention ! Avant tout travaux de rééquipement et de
montage, débrancher la fiche d’alimentation
Monter le support de dressage (A) avec 2 vis Allen demi-
rondes (B) M6 x20 mm et 2 rondelles de 6 mm (B) sur la
paroi latérale de la machine à raboter. Glisser le rail de
butée (C) avec les encoches dans les écrous pré-montés
et serrer ces derniers au moyen des 4 vis papillon (E).
Alignement de la butée de dressage Fig. 3
Régler la butée à un angle de 90 ° et la serrer avec la
vis à clé (H). Régler la vis à fente (F) jusqu’à la butée et
la bloquer avec l’écrou. Puis régler la butée sur 45° et
bloquer avec la vis à clé (H). Ensuite régler la vis Allen
(G) jusqu’à la butée et bloquer avec l’écrou.
Vérifier les angles à l’aide d’un échantillon et régler de
nouveau l’échelle (I) si cela est nécessaire.
Montage protection de l’arbre de rabot Fig. 5, 6
La vis à tête moletée (6) sert à soulever la protection de
l’arbre de rabot (1).
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT 106 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT 106 Woodster in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info