782513

Scheppach MST216 Manual

69
Zoom out
Zoom in
Previous page
1/84
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 69
• With the drag guide (21) not xed in place (21):
Pull the machine head (4) all the way to the front. Lower the handle (1)
to the very bottom by applying steady and light downward pressure.
Now push the machine head (4) slowly and steadily to the very back
until the saw blade (6) has completely cut through the work piece.
• When the cutting operation is completed, move the machine head
back to its upper (home) position and release the ON/OFF button (2).
Attention! The machine executes an upward stroke automatically due
to the return spring, i.e. do not release the handle (1) after completing
the cut; instead allow the machine head to move upwards slowly whilst
applying light counter pressure.
8.4 Crosscut 90° and turntable 0°−45° (g. 1/7/8)
The sliding compound mitre saw can be used to make crosscuts of
0°−45° to the left and 0° -45° to the right in relation to the stop rail.
Attention! For 90° crosscuts, the moveable stop rail (16a) must be xed
in the inner position.
• Open the set screw (16b) for the moveable stop rail (16a) and push the
moveable stop rail (16a) inwards.
• The moveable stop rail (16a) must be xed far enough in front of the
innermost position that the distance between the stop rail (16a) and
the saw blade (6) amounts to a minimum of 8 mm.
• Before making the cut, check that the stop rail (16a) and the saw blade
(6) cannot collide.
• Secure the set screw (16b) again.
• Loosen the locking handle (11) if tightened, pull up the latched position
lever (35) with your index nger and use the locking handle (11) to set
the rotary table (14) to the desired angle.
• The pointer (12) on the rotary table must match the desired angle on
the scale (13) on the xed saw table (15).
• Re-tighten the handle (11) to secure the rotary table (14).
• Cut as described under section 8.3.
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MST216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MST216 in the language / languages: English, German as an attachment in your email.

The manual is 5.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info