782513
70
Zoom out
Zoom in
Previous page
1/84
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
70 | GB
8.5 Precision adjustment of the stop for mitre cut 45° (g. 1/2/5/9/10)
No stop angle included.
Lower the machine head (4) and secure it using the locking bolt (23).
Fix the rotary table (14) in the 0° position.
Attention! For mitre cuts (inclined saw head), the left side of the move-
able stop rails (16a) must be xed in the outer position.
Open the set screw (16b) for the moveable stop rail (16a) and push the
moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be xed far enough in front of the
innermost position that the distance between the stop rail (16a) and
the saw blade (6) amounts to a maximum of 8 mm.
The right side of the moveable stop rails (16a) must be in the inner
positiion.
Before making a cut, check that the stop rail (16a) and the saw blade
(6) cannot collide.
Loosen the set screw (22) and use the handle (1) to angle the machine
head (4) 45° to the left.
45° position angle stop (B) between the saw blade (6) and rotary table
(14).
Loosen the lock nut (27a) and adjust the adjustment screw (27) until
the angle between the saw blade (6) and the rotary table (14) is pre-
cisely 45°.
Re-tighten the lock nut (27a).
Subsequently check the position of the angle indicator. If necessary,
loosen the pointer (19) using a Phillips screwdriver, set to position 45°
on the angle scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°45° and turntable 0° (g. 1/2/11)
The sliding compound mitre saw can be used to make mitre cuts of 0° -
45° in relation to the work face.
Attention! For mitre cuts (inclined saw head), the left side of the move-
able stop rails (16a) must be xed in the outer position.
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MST216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MST216 in the language / languages: English, German as an attachment in your email.

The manual is 5.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info