Manual Scheppach KZS-UG1800 Primaster (page 25 of 44) (English, German, French)

782504

Zoom out

Zoom in

1/44

25GB

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (14) loosen the set

screw (11) approx. 2 turns.

• Turn the rotary table (14) and pointer (12) to the de-

sired angle measurement on the scale (13) and secure

with the set screw (11).

• Pressing the machine head (4) lightly downwards and

removing the locking bolt (23) from the motor bracket

at the same time disengages the saw from the low-

est position.

• Swing the machine head (4) up until the release lever

(3) latches into place.

• It is possible to secure the clamping device (7) to the

left or right on the stationary saw bench (15).

• Attach the workpiece supports (8) to the xed saw

table (15) as shown in Figure 5 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45° to

the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (14).

• Unscrew lock nut (27a)

• Adjust the adjusting screw (27) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• Tighten the lock nut (27a).

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 0° on the angle

scale (18) and re-tighten the retaining screw.

8.3 Cross cut 90° and turntable 0° (Fig. 3/8)

In the case of cutting widths up to approx. 100 mm it is

possible to x the traction function of the saw with the

set screw (20) in the rear position. In this position the

machine can be operated in cross cutting mode. If the

cutting width is over 100 mm then it is necessary to en-

sure that the set screw (20) is loose and the machine

head (4) can move.

Attention! For 90° cross cuts, the moveable stop rail

(16a) must be xed in the inner position.

• Open the set nut (16b) on the moveable stop rail

(16a) and push the moveable stop rail (28) inwards.

• The moveable stop rail (16a) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (16a) and the saw blade

(6) is no more than 8 mm.

• Before making the cut, check that no collision could oc-

cur between the stop rail (16a) and the saw blade (6).

• Tighten the set nut (16b) again.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

(4) and x it in this position if required (dependent on

the cutting width).

• Place the piece of wood to be cut at the stop rail

(16) and on the turntable (14).

• Lock the material with the clamping device (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (4).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (21) xed in place:

• use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until the

saw blade (6) has completely cut through the work

piece.

• With the drag guide (21) not xed in place:

• pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by apply-

ing steady and light downward pressure. Now push

the machine head (4) slowly and steadily to the

very back until the saw blade (6) has completely cut

through the work piece.

• When the cutting operation is completed, move the

machine head (4) back to its upper (home) position

and release the ON/OFF button (2).

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not re-

lease the handle (1) after completing the cut; instead

allow the machine head to move upwards slowly

whilst applying light counter pressure.

8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)

The crosscut saw can be used to make crosscuts of 0°

-45° to the left and 0° -45° to the right in relation to the

stop rail.

Important. To make 90° crosscuts, the adjustable stop

rail (16a) must be xed at the inner position.

• Open the set nut (16b) for the adjustable stop rail

and push the adjustable stop rail inwards.

• The adjustable stop rail (29) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set nut (16b) again.

• Loosen set screw (26).

• Use the handle (11) to adjust the rotary table (14)

to the desired angle. The pointer (12) on the rotary

table must match the desired angle on the scale (13)

on the xed saw table (15).

• Re-tighten the set screw (11) in order to secure the

rotary table (14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (Fig. 1/10/11)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (4) 45° to the left.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KZS-UG1800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KZS-UG1800 Primaster Manual

Product: