Manual Scheppach KZS-UG1800 Primaster (page 23 of 44) (English, German, French)

782504

Zoom out

Zoom in

1/44

23GB

reduced noise development, insofar as possible.

Maintain the electric tool and tool attachments

regularly and if necessary, initiate repairs in

order to reduce noise.

–Report faults on the electric tool, protective

devices or the tool attachment to the person

responsible for safety as soon as they are dis-

covered.

3 Safe work

–Only use saw blades for which the maximum

permissible speed is not lower than the maxi-

mum spindle speed of the machine and which

are suitable for the material to be cut.

–Make sure that the saw blade does not touch

the rotary table in any position by pulling out the

mains plug and rotating the saw blade by hand

in the 45° and 90° position. If necessary, read-

just the saw head.

–When transporting the electric tool, only use

the transport devices. Never use the protective

devices for handling or transport.

–Make sure that the lower part of the saw blade is cov-

ered during transport, e.g. by the protective device.

–Be sure to only use spacers and spindle rings

specied by the manufacturer as suitable for the

intended purpose.

–The oor around the machine must be level,

clean and free of loose particles, such as chips

and cutting residues.

–Do not remove any cutting residues or other

parts of workpieces from the cutting zone while

the machine is running and the saw unit is not

at rest.

–Make sure that the machine is always secured

on a workbench or a table if at all possible.

–Support long workpieces (e.g. with a roller table)

to prevent them sagging at the end of a cut.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair active

or passive medical implants under certain conditions. In

order to prevent the risk of serious or deadly injuries, we

recommend that persons with medical implants consult

with their physician and the manufacturer of the medical

implant prior to operating the electric tool.

SAFETY INSTRUCTIONS FOR THE HANDLING OF

SAW BLADES

1 Only use insertion tools if you have mastered their

use.

2 Observe the maximum speed. The maximum

speed specied on the insertion tool may not be

exceeded. If specied, observe the speed range.

3 Observe the motor / saw blade direction of rotation.

4 Do not use any insertion tools with cracks. Sort out

cracked insertion tools. Repairs are not permitted.

5 Clean grease, oil and water off of the clamping

surfaces.

6 Do not use any loose reducing rings or bushes for

the reducing of holes on saw blades.

7 Make sure that xed reducer rings for securing the

insertion tool have the same diameter and have at

least 1/3 of the cutting diameter.

8 Make sure that xed reducer rings are parallel to

each other.

9 Handle insertion tool with caution. They are ideally

stored in the originally package or special contain-

ers. Wear protective gloves in order to improve

grip and to further reduce the risk of injury.

10 Prior to the use of insertion tools, make sure that

all protective devices are properly fastened.

11 Prior to use, make sure that the insertion tool

meets the technical requirements of this electric

tool and is properly fastened.

12 Only use the supplied saw blade for cutting wood,

never for the processing of metals.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unpro-

tected eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reecting sur-

faces and persons or animals. Even a laser beam

with a low output can cause damage to the eyes.

• Caution - methods other than those specied here

can result in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure

to the beam can occur.

• If the mitre saw is not used for an extended period

of time, the batteries should be removed.

• The laser may not be replaced with a different type

of laser.

• Repairs of the laser may only be carried out by the

laser manufacturer or an authorised representative.

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted

with the correct polarity (+ and –), as indicated on

the battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

5 Do not mix old and new batteries or batteries of

different types or manufacturers! Replace an entire

set of batteries at the same time.

6 Immediately remove used batteries from the de-

vice and dispose of them properly! Do not dispose

batteries with household waste. Defective or used

batteries must be recycled according to Directive

2006/66 / EC. Give back batteries and / or the device

has been offered to the collective facilities. About

disposal facilities you can inform by your municipal

or city government.

7 Do not allow batteries to heat up!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KZS-UG1800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KZS-UG1800 Primaster Manual

Product: