Manual Scheppach KZS-UG1800 Primaster (page 27 of 44) (English, German, French)

782504

Zoom out

Zoom in

1/44

27GB

• Replacing the battery: Switch off the laser (33).

Remove the battery compartment cover (36). Re-

move the batteries and replace with new batteries

(2 x 1.5 Volt Type LR 03 Micro, AAA) Check that

the battery terminals are positioned correctly when

inserting new batteries. Close the battery compart-

ment (35) again.

8.12 Adjusting the laser (Fig. 21)

If the laser (33) ceases to indicate the correct cutting line,

you can readjust the laser. To do so, open the screws

(37) and set the laser by moving sideways to that the

laser beam strikes the teeth of the saw blade (6).

8.13 Installing the Untergestells (g. 18)

A 2 transversal frames, top (400mm)

B 2 longitudinal frames, top (430 mm)

C 2 transversal struts (470mm)

D 2 longitudinal struts (560 mm)

E 4 feet

F 4 rubber feet

Bolts

• Place frames parts on an even surface – Attention:

parts of equal length must face each other!

• Attach each of the 4 feet with 2 bolts, washers, spring

washers and nuts and tighten by hand.

• Screw the 4 struts in place with 4 bolts.

• Align the frame so it is right-angled and tighten all

bolts.

• Attach the rubber feet und place base frame on the

ground.

• Mount saw and fasten it with 4 hexagon bolts.

9. Transport

• Tighten the set screw (11) in order to lock the rotary

table (14)

• Activate the release lever (3), press the machine

head (4) downwards and secure with the safety pin

(23). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (20) in rear position.

• Carry the equipment by the xed saw table (15).

• When reassembling the equipment proceed as de-

scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time us-

ing a cloth. In order to extend the service life of the tool, oil

the rotary parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive products.

Brush inspection

Check the carbon brushes after the rst 50 operating

hours with a new machine, or when new brushes have

been tted. After carrying out the rst check, repeat the

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

• The product meets the requirements of

EN 61000-3-11 and is subject to special connection

conditions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavorable conditions in the power supply the

product can cause the voltage to uctuate temporarily.

• The product is exclusively intended for use at con-

nection points that have a continuous current-carry-

ing capacity of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets the specied requirements.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the mo-

tor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KZS-UG1800 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KZS-UG1800 Primaster Manual

Product: