782095

Scheppach Kity DRA 260 Manual

29
Zoom out
Zoom in
Previous page
1/36
Next page
29
metal.
Attention:
In case of a bad condition of the electrical system, the
performance can drop for a short period of time. Ask
a specialist.
m Electrical connections
The electric motor installed is completely wired ready
for operation.
The connection meets the requirements of the German
standards VDE and DIN.
The connection to the electric power supply to be ef-
fected by the customer as well as the extension cable
must also meet these requirements.
Connection and repair work on the electrical installation
may be carried out by a qualied electrician only.
Important hints:
The electric motor has been design for operating mode
S1.
Defective electrical connection cables:
Electrical connection cables often suffer insulation
damage. Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinks resulting from incorrect attachment or laying of
the connection cable.
• Cuts resulting from running over the connecting cable.
• Insulation damage resulting from forcefully pulling out
of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely
hazardous.
Check electrical connection cables regularly for dam-
age. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the regu-
lations VDE and DIN. Only use cables marked "HO 7
RNF". This is a binding regulation.
Single-phase motor
• The voltage of the power supply must be 230 V / 50
Hz.
• Extension cables up to a length of 25 m must have a
cross-section of 1.5 mm², and beyond 25 m at least
2.5 mm².
• The connection to the mains must be protected with
a 16 A slow-acting fuse.
In the event of enquiries please specify the following
data:
• Type of current of the motor
• Data recorded on the machine's rating plate
• Data recorded on the switch's rating plate
If the motor has to be returned, it must always be dis-
patched with the complete driving unit and switch.
commerce approprié.
Les outils en aluminium doivent être traités uniquement
avec un liquide adapté et n’agressant pas ce type de
métal.
Attention:
Un mauvais réseau électrique peut affecter la puis-
sance de la machine. Consulter un électricien.
m Branchement électrique
Le moteur électrique est prêt à fonctionner. Le bran-
chement correspond aux normes allemandes VDE et
DIN en vigueur.
Le raccordement électrique que doit effectuer le client
ainsi que les câbles de rallonge utilisés doivent égale-
ment correspondre à ces normes.
Les branchements et réparations de l’équipement élec-
trique ne doivent être effectués que par un électricien
qualié.
Iimportant:
Le moteur électrique a été construit pour le mode de
fonctionnement S1.
Câbles électriques défectueux:
Il arrive fréquemment que l’isolation des câbles élec-
triques présente des avaries. Les causes en sont:
• Ecrasements, si le câble est passé sous les portes
ou les fenêtres.
• Pliures dues à une mauvaise xation ou un mauvais
guidage du câble.
• Coupures dues à un écrasement du câble.
• Extractions violentes du câble de la prise murale.
• Fissures due au vieillissement de l'isolation.
Il est déconseillé d’utiliser des câbles électriques qui
présentent ce type d’avaries. Danger de mort.
Vérier régulièrement les câbles électriques. Veiller à
ce que le câble ne soit pas branché au secteur pendant
la vérication.
Les câbles électriques doivent correspondre aux
normes VDE et DIN en vigueur. Utiliser des câbles
marqués «HO 7 RNF».
Moteur monophasé
• La tension du secteur doit être de 230 V / 50 Hz.
• Les câbles de rallonge d’une longueur maximale de
25 m doivent avoir des conducteurs de 1,5 mm², ceux
d’une longueur supérieure à 25 m doivent avoir des
conducteurs de 2,5 mm².
• Le branchement au réseau doit être équipé d’un
fusible à action retardée de 16 A.
Pour toutes informations complémentaires, veuillez
fournir les indications suivantes:
• Courant du moteur
• Données se trouvant sur la plaque signalétique de
la machine
• Données se trouvant sur la plaque signalétique de
l’interrupteur
En cas de renvoi du moteur, toujours envoyer l’unité
moteur complète avec l’interrupteur.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Kity DRA 260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Kity DRA 260 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info