782095

Scheppach Kity DRA 260 Manual

31
Zoom out
Zoom in
Previous page
1/36
Next page
31
• The product meets the requirements of EN 61000-3-11 and is subject to special connection conditions. This means
that use of the product at any freely selectable connection point is not allowed.
• Given unfavorable conditions in the power supply the product can cause the voltage to uctuate temporarily.
• The product is intended solely for use at connection points that
a) do not exceed a maximum permitted supply impedance “Z”, or
b) have a continuous current-carrying capacity of the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consultation with your electric power company if necessary, that the con-
nection point at which you wish to operate the product meets one of the two requirements, a) or b), named above.
Finding the causes of any troubles turned up and their remedy always demands extra attention and caution. Before starting
trouble-shooting, always pull the power supply plug.
In the following, some of the most frequent defects and their causes are listed. In case of any further defects, please
call your dealer.
Problem Possible Cause Remedy
Machine cannot be switched on. No power supply.
Carbon brush worn.
Check power supply.
Take machine to your service point.
Machine switches automatically off
during idle run. No mains supply. Check fuses.
Due to the integrated low-voltage
protection, the machine does not re-
start automatically. Upon return of the
voltage, the machine must be switched
on again.
Machine stops during planing. Overload protection reacts due to blunt
knives, infeed too fast, or chip removal
too thick.
Before work is continued, replace
knives or let cool down the motor.
Response of the overload protection. Too much chip removal
Too fast feed
Blunt knives
Before continuing work, replace the
knives or wait for the motor to cool
down.
Planed surface not smooth. Infeed too fast.
Blunt knives.
Irregular feed.
Reduce infeed speed.
Replace knives.
Apply constand pressure and reduce
feed.
When thicknessing, chip ejection
obstructed (without dust extractor). Chip removal too important.
Blunt knives.
Wood too humid.
Reduce chip removal.
Replace knives.
When surface planing, chip ejection
obstructed (without dust extractor) Chip removal too important.
Infeed to fast.
Blunt knives.
Wood too humid.
Reduce chip removal.
Replace knives.
With surface planing and thicknessing,
chip ejection obstructed (with dust
extractor).
Suction performance too weak. Use a dust extractor unit having an
air-flow rate at the suction connection
of at least 20 m/s.
Rpm drops during planing. Chip removal too important. Reduce chip removal.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Kity DRA 260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Kity DRA 260 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info