782095

Scheppach Kity DRA 260 Manual

25
Zoom out
Zoom in
Previous page
1/36
Next page
25
Thicknessing:
• Following the scale and using the handle (O) on the
spindle, set the thicknessing table to the desired
height. 1 rotation = 3 mm.
• Slide narrow wood to the centre of the thickness table.
For thickness planing and also jointing the use of spray
lubrication or compound. After a long period of use, or
when planing humid wood, it can happen that the work
piece is not further pulled in.
Warning:
In case of a defect, switch off the machine at once. Do
not remove any chips or splinters from the tables while
the machine is running. Work pieces below 250 mm
length may not be planed.
Changing the knives (Fig. 11)
• Put the main switch of the machine to OFF position.
• Pull the power supply plug from the socket.
• Block the cutter block guard in the lifted position.
• Release and remove the four knife clamping screws.
• Lift the knives and knife support from the cutter block.
• Remove the chips and any resin from the cutter block
and knife support.
• Place new knives into the cutter block and x them
with the rectangle slots in both screw heads. (With
these two screws, height-adjustment of the knife is
done.)
• Place the knife support onto the knife.
• Slightly tighten the four clamping bolts.
• Repeat these actions for the second knife.
• Then adjust the planer/thicknesser knives exactly with
the output table. Use a ruler that you put onto the
output table.
• By the two set screws, the knife can be adjusted for
height.
• By turning the cutter block and using the ruler, you can
see the height adjustment.
• The knife is exactly set, when the ruler is moved by
the knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
must be tightened (8.4 N/m).
Please mind:
• Sharp planer/thicknesser knives guarantee a clean
planing surface and put less stress on the motor.
• Observe all knifes to have the same width (unbalance),
when nish-grinding. The minimum width of the knifes
is 20mm.
• The planer/thicknesser blades used on this machine
are not suitable for rebating and dovetailing.
• Finally lower the cutter block guard again onto the
table. Cover the cutter block and block it with the star
grip screw.
pousse-bois.
Rabotage:
• Régler la table de rabotage à la hauteur désirée
à l’aide de la manivelle (O) et lire la cote sur la
graduation. 1 tour de manivelle = 3 mm.
• Introduire un morceau de bois étroit au centre de la
table de rabotage.
Pour le rabotage et pour le dégauchissage il est recom-
mandé d’utiliser un lubriant spécial en spray ou en
pâte. Après une période d’utilisation prolongée ou le
rabotage de bois humide, l’avance du bois peut se
bloquer.
Avertissement:
En cas de panne, arrêter la machine immédiatement.
Ne pas enlever les copeaux pendant que la machine
est en marche. Il est interdit de raboter des pièces de
bois d’une longueur inférieure à 25 cm.
Remplacement des fers de rabot (Fig. 11)
• Mettre l'interrupteur à la position «Arrêt».
• Débrancher la prise d’alimentation.
• Bloquer le protecteur à pont de l'arbre de rabotage à
sa position la plus haute.
• Desserrer et enlever les 4 vis de serrage des fers.
• Enlever les fers et les cales de l'arbre.
• Enlever les copeaux et la résine des cales et de
l’arbre.
• Mettre le nouveau fer en place sur l’arbre et le xer en
plaçant les fentes rectangulaires sur les 2 têtes de vis.
(Ces 2 vis servent à régler la hauteur du fer)
• Mettre la cale sur le fer.
• Serrer légèrement les 4 vis de serrage.
• Répéter la procédure pour le deuxième fer.
• Ensuite, régler précisément la hauteur des fers par
rapport à la table de sortie, en utilisant une règle.
• La hauteur des fers se règle à l’aide des deux vis de
réglage.
• Vérier la hauteur des fers en faisant tourner l’arbre,
tout en maintenant la règle sur place.
• Le fer est correctement positionné si la règle est
poussée de 3 mm.maximum par les fers an faisant
tourner l’arbre
• Resserrer ensuite toutes les vis
fermement (avec un couple de 8,4 Nm)
Attention:
• Ne travaillez qu'avec des fers bien affûtés. Ils
ménagent le moteur et garantissent un résultat parfait.
• Lors du réaffûtage, veiller à ce que toutes les lames
aient la même largeur (balourd). La largeur minimale
des lames est de 20 mm.
• Les fers utilisés sur cette machine ne sont pas
appropriés pour réaliser des languettes ou des tenons.
• Abaisser le protecteur à pont sur l'arbre de rabotage
pour le couvrir et resserrer avec la poignée.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Kity DRA 260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Kity DRA 260 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info