782095

Scheppach Kity DRA 260 Manual

21
Zoom out
Zoom in
Previous page
1/36
Next page
21
Before transporting, pull the power supply plug.
During transport, the cutter block guard must be set in
the lowest position.
Unpacking the machine
Check the contents of any possible transport damage.
In case of a damage, inform immediately the forward-
ing agent. Check the contents for completeness. Inform
immediately the dealer in case of any missing parts.
The complete machine is shipped in one single carton
box. Any additional parts that have to be attached to
the machine, must be identied before starting the as-
sembly.
Scope of delivery Fig. 2
1 Planing and thicknessing machine
2 Ripping fence
3 Handle
4 Suction connector
5 Allen key
6 Ribbed belt
Assembly
Assembling trimming endstop unit Fig. 3
Attention! Device must be unplugged from mains during
any retooling or assembly work
Install the jointing bracket (A) with 2 inner hexagon bolts
(B) M5x20mm to the side wall of the jointing table.
Justifying the trimming endstop Fig. 4
Postion the endstop at a 90 ° angle, and clamp it in place
with the toggle screw (H). Now place the cross-slotted
screw (F) against the endstop and secure it with the
nut. Then position the endstop at 45° and clamp it in
place with the clamping screw (H). Next, place the allen
screw (G) against the endstop and secure it with the nut.
Now check both brackets with a sample and re-justify
the scale if required.
Adjusting the stop rail Fig.4
The stop rail (C) in the area of the stop bolt (E) can be
displaced by loosening the clamping lever (D).
Planer shaft guard Fig. 5
The clamping handle (J) serves the purpose of lifting
and xing the planer shaft guard (K)
dégauchissage.
Pour le transport, débrancher la prise du secteur.
Lors du transport, le protecteur de l’arbre de rabotage
doit se trouver dans la position la plus basse.
Déballage de la machine
Vérier dès la livraison, qu’aucune pièce n’a été détério-
rée pendant le transport. En cas de réclamation, infor-
mer aussitôt le livreur. Vérier que la livraison est bien
complète. Si des pièces manquent, informer aussitôt
le vendeur.
La machine est expédiée dans un seul carton. Les
pièces qui doivent être montées sur la machine doivent
être repérées et identiées avant le début du montage.
Ensemble de livraison Fig. 2
1. Raboteuse-dégauchisseuse
2.Guide de dégauchissage
3. Manivelle
4. Ejecteur de copeaux
5. Clé allen
6. Courroie crantée
Montage
Montage du guide de dégauchissage Fig. 3
Attention ! Avant tous travaux de préparation et de
montage, débrancher la che d’alimentation
Assemblez le support du guide de dégauchissage (A)
avec les 2 vis à tête hexagonale (B) M5 x 20 mm sur le
côté de la table de dégauchissage.
Réglage du guide de dégauchissage Fig. 4
Régler le guide à un angle de 90 ° et le bloquer avec la
manette (H). Visser la vis cruciforme (F) jusqu’en butée
et la bloquer avec le contre-écrou. Positionner le guide
à 45° et le bloquer avec la manette (H). Amener la vis à
six pans creux (G) en butée et la bloquer avec le contre-
écrou.
Vérier les angles à l’aide d’un gabarit et régler de
nouveau la graduation (I) si cela est nécessaire.
Réglage du rail du guide de dégauchissage Fig. 4
En desserrant le levier de serrage (D), le rail (C) peut
être déplacé entre les vis de butée (E).
Protecteur à pont de l'arbre de rabot Fig. 5
La poignée de blocage (J) sert à verrouiller le protecteur
à pont de l'arbre de rabot (K).
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Kity DRA 260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Kity DRA 260 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info