782423

Scheppach KGZ251 Manual

21
Zoom out
Zoom in
Previous page
1/136
Next page
21
have read and understood the safety and operational instruc-
tions.
Basic Pullover Mitre Saw Operations
• Always use the clamp 17 to hold the work piece firmly.
2 holes are provided for the clamp.
• Always position the work piece against the fence. Any
piece that is bowed or warped and cannot be held flat
on the table or against fence may trap the blade and
should not be used.
• Never place hands near the cutting area. Keep hands
outside the ”No Hands Zone” which includes the en-
tire table and is labelled by ”No Hands” symbols.
WARNING! To avoid injury from materials being thrown, un-
plug the saw to avoid accidental starting, and then remove
small materials.
Chop Cut (Fig. 5)
• For chop cutting, slide the cutting head to the rear
position as far as it will go, and lock the carriage 1 by
the lock handle 2.
Mitre Cut
• Make sure the extension fence is secured in the cor-
rect position.
• Release the mitre locking button and move the table to
the desired angle. Every five degrees, angles from 0° to
45° can be fast and precisely set. Let the mitre button
snap in and fix the angle with the clamping screw.
• Activate the switch, then press the blade guard lock
lever to lower the cutting head down.
et du réglage et d’avoir lu et compris les consignes de sécu-
rité et le mode d’emploi.
Consignes générales
• Toujours utiliser le serre-joint 17 pour immobiliser la
pièce à scier. 2 trous sont prévus pour le serre-joint.
• Toujours placer la pièce à couper contre le guide. Ne
pas utiliser de pièce cintrée ou tordue ou de pièce qu’il
est impossible de maintenir à plat sur le plateau ou
contre le guide, car elle risque de bloquer la lame.
• Ne jamais placer les mains dans la zone de coupe, qui
comprend l’ensemble du plateau et est indiquée par
des symboles „Pas de mains”.
ATTENTION! Pour éviter d’être blessé par des projections de
matériaux, débrancher la scie pour l’empêcher de se mettre
en marche accidentellement et enlever les petits morceaux
de matériaux.
Coupe de refend (Fig. 5)
• Pour la coupe de refend, faire glisser la tête de coupe
vers l’arrière aussi loin qu’elle peut aller et bloquer le
chariot 1 à l’aide de la manette de blocage 2.
Coupe d’onglet
• S’assurer que le guide-rallonge est assujetti dans la
bonne position.
• Relâcher le bouton de serrage à onglets et tourner la
table à l’angle désiré. Par le trame à chaque 5 degrés,
tous les angles de 0° à 45° peuvent être réglés rapide-
ment et à haute précision. Laisser bloquer le bouton de
serrage et fixer l’angle à l’aide de la vis de blocage.
• Mettre la scie en marche, puis appuyer sur le levier
du protège-lame supérieur pour abaisser la tête de
coupe.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KGZ251 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KGZ251 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish, Finnish as an attachment in your email.

The manual is 4.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info