782423

Scheppach KGZ251 Manual

19
Zoom out
Zoom in
Previous page
1/136
Next page
19
Adjusting the laser beam, Fig.4
1 To adjust the laser beam, you need a wooden plank (ca.
200 mm x 300 mm). Draw a line in a right angle and
position the plank at the locating face of the table.
2 Adjust the marking central to the saw blade and fix it
with the clamping jaw.
3 Switch on the laser with the On-Off switch.
4 Turn the screw (1) until the laser beam is parallel to
the drawn line.
5 The lateral correction can be done by loosening the
screws (2) and moving of the laser unit.
Attention: You can adjust the laser beam so that it moves
at the side or in the middle of the cut.
6 Re-tighten both screws (2) and re-adjust, if neces-
sary.
Connecting to the Power Supply
Check that the power supply and outlet used are in ac-
cordance with your mitre saw. Have a look at the rating
plate of the motor or the rating on the mitre saw. Any
changes should always be carried out by a qualified elec-
trician.
This is a double insulated tool which eliminates the need
for an earthed power supply system.
WARNING! Avoid contact with the terminals on the plug when
installing (removing) the plug to (from) the power supply out-
let. Contact will cause a severe electrical shock.
Using an Extension Lead
The use of any extension lead will cause some loss of
power. To keep this to a minimum and to prevent over-
heating and possible motor burn-out, ask advice from a
qualified electrician to determine the minimum wire size
of the extension lead.
The extension lead should be equipped with an earthed
type plug that fits the power supply outlet at one end,
and with an earthed type socket that fits the plug of this
machine at the other end.
Mounting the Tool
Note:
We highly recommend that you bolt this mitre saw se-
curely to a work bench to gain the maximum stability of
your machine.
• Locate and mark the four bolt holes on the bench.
• Drill the bench with a ø 10 mm drill bit,
• Bolt the mitre saw on to the bench with bolts, washers
and nuts. Note that these fasteners are not supplied
with the machine.
Operating the Tool
WARNING! Never connect the plug to the power source outlet
until all Installations and adjustments are completed and you
Réglage du rayon laser, Fig.4
1 Pour ajuster le rayon laser, prendre une planche (en-
viron 200 mm x 300 mm) Marquer une ligne à angle
droit et placer la planche sur la surface de butée de
la table.
2 Aligner le marquage de manière centrale par rapport à
la lame de scie et serrer avec la bride de serrage.
3 Allumer le laser à líaide de líinterrupteur marche/
arrêt
4 Tourner la vis (1) jusqu'à ce que le rayon laser soit
parallèle à la ligne marquée.
5 La correction latéralement peut être effectuée par des-
serrage des deux vis (2) et déplacement de l'unité à
laser.
à noter : Vous pouvez régler le rayon laser de sorte qu'il
suive le côté ou le centre de la coupe.
6 Resserrer les deux vis (2) et refaire un réglage fin si
nécessaire.
Branchement de la scie
S’assurer que le courant et la prise utilisée correspondent
à ce dont la scie a besoin. Voir les spécifications qui fi-
gurent sur la plaque signalétique du moteur ou celles qui
figurent sur la scie. Tout changement doit être effectué
par un électricien qualifié.
Ayant une double épaisseur d’isolement, la scie n’a pas
besoin d’une alimentation mise à la terre.
ATTENTION : Eviter tout contact avec les pointes de la fiche
quand on l’enfiche dans la prise de courant ou qu’on l’en re-
tire. Tout contact causera un choc électrique dangereux.
Emploi d’une rallonge
L’emploi d’une rallonge entraîne automatiquement une
certaine perte de courant. Pour minimiser cette perte et
empêcher le moteur de s’échauffer et de griller, deman-
der à un électricien qualifié quel calibre minimal de fil la
rallonge doit avoir.
La rallonge doit être munie, à une extrémité, d’une fiche
mâle avec mise à la terre, qui s’enfiche dans la prise de
courant et, à l’autre extrémité, d’une fiche femelle avec
mise à la terre, qui s’enfiche dans la scie.
Montage de la scie
N. B. :
Il est vivement recommandé de boulonner la scie à un
établi pour lui assurer le maximum de stabilité.
• Repérer et marquer l’emplacement des quatre trous
de fixation sur l’établi.
• Percer les trous dans l’établi avec un foret de 10
mm.
• Boulonner la scie à l’établi à l’aide de boulons, rondel-
les et écrous (non fournis avec la scie).
Mode d’emploi
ATTENTION! Ne pas enficher la fiche dans une prise de cou-
rant avant d’avoir terminé toutes les étapes de l’installation
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KGZ251 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KGZ251 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish, Finnish as an attachment in your email.

The manual is 4.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info