782423
17
Zoom out
Zoom in
Previous page
1/136
Next page
17
m Assembly
WARNING! For your own safety, never connect the plug to
power source outlet until all assembly steps are completed
and you have read and understood the safety and operational
instructions.
Lift the saw from the packaging and place it on your work
bench.
Installation of the saw dust bag (Fig. 2)
Slide the saw dust bag (2) onto the discharge opening (1)
in the engine area.
Setting the Tool
Note:
This tool is accurately adjusted before shipping from the
factory. Check the following accuracy and readjust if nec-
essary in order to obtain the best results in operation.
Adjusting the Bevel Stops at 90° and 45° (Fig. 3)
• Loosen the Bevel Lock Handle and move the cutting
head all the way to the right and tighten the Bevel
Lock Handle 1.
• Use a square to set the blade at 90° to the table.
• If an adjustment is necessary, loosen the lock nut 2
and adjust the bolt 3 using the supplied wrench so that
the blade is 90° to the table.
• Tighten the lock nut.
• Adjust the bevel indicator 5 to the 0 mark using the
screw.
• To adjust the 45° stop, follow the same procedure as
the 90° but move the cutting head to the left and use
the lock nut 2 and bolt 3.
Adjusting the Fence
• Lower the cutting head and push in the lock pin. Make
sure the table is in 0 mitre position.
• Place a combination square against the fence and next
to the saw blade.
• If the blade does not contact the square, loosen the
screws .
• Adjust the fence so that the fence has full contact with
the square. Tighten the screws.
une opération de quelque nature que ce soit, relâcher
le bouton sur la poignée pour désactiver la machine.
m Montage
ATTENTION! Dans l’intérêt de votre sécurité, ne pas enficher
la fiche dans une prise de courant avant d’avoir terminé tou-
tes les étapes du montage et d’avoir lu et compris les consi-
gnes de sécurité et le mode d’emploi.
Retirer la scie de son carton et la placer sur l’établi.
Installation du sac à poussières (Fig. 2)
Pousser le sac à poussières (2) sur l'orifice de sortie (1)
dans la zone moteur.
Réglage de la scie
N. B. :
La scie a été ajustée avec précision en usine avant son
expédition. Pour obtenir les meilleurs résultats, faire les
vérifications suivantes de la précision et ajuster de nou-
veau au besoin.
Réglage des angles de chanfrein de 90° et 45° (Fig. 3)
• Desserrer la manette de blocage de chanfrein et pous-
ser la tête de coupe vers la droite aussi loin qu’elle
peut aller, puis resserrer la manette de blocage 1.
• A l’aide d’une équerre, ajuster la lame pour la mettre
perpendiculaire au plateau.
• Si un ajustement s’impose, desserrer le contre-écrou
2 et ajuster le boulon 3 à l’aide de la clé fournie à
cette fin, de façon que la lame soit perpendiculaire
au plateau.
• Serrer le contre-écrou.
• Amener l’indicateur de chanfrein 5 à la graduation 0
en tournant la vis.
• Pour le réglage à 45°, procéder de la même façon,
mais pousser la tête de coupe vers la gauche et utiliser
le contre-écrou 2 et le boulon 3.
Adjustement du guide
• Abaisser la tête de coupe et la bloquer avec la gou-
pille de sécurité. S’assurer que le plateau est dans la
position d’onglet 0.
• Placer l’un des bras d’une équerre combinée contre le
guide et l’autre contre la lame de scie.
• Si la lame ne touche pas l’équerre, desserrer les vis.
• Ajuster le guide de façon qu’il touche l’équerre tout
au long. Serrer les vis.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KGZ251 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KGZ251 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish, Finnish as an attachment in your email.

The manual is 4.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info