782092

Scheppach HT1050 Manual

27
Zoom out
Zoom in
Previous page
1/108
Next page
27
The table surfaces as well as the infeed and output
rollers must always be kept free from resin.
• Regularly clean infeed and output rollers.
• In order to avoid overheating of the motor, regularly
check the air openings for any dust sticking on.
• After a longer period of use, it is recommended to
have the machine checked by an authorized dealer
service.
Tool care:
• Cutter block, clamping devices, knife supports and
knives must be regularly cleaned from resin, as
a clean tool improves the planing quality. To this
purpose, clamping devices, knife supports and knives
can be put in a common resin remover for 24 hours.
• Resin from aluminium tools may only be removed with
cleaning liquids not being aggressive to this type of
metal.
Attention:
In case of a bad condition of the electrical system, the
performance can drop for a short period of time. Ask
a specialist.
m Electrical connections
The electric motor installed is completely wired ready
for operation.
The connection meets the requirements of the German
standards VDE and DIN.
The connection to the electric power supply to be ef-
fected by the customer as well as the extension cable
must also meet these requirements.
Connection and repair work on the electrical installation
may be carried out by a qualied electrician only.
Important hints:
The electric motor has been design for operating mode
S1.
Defective electrical connection cables:
Electrical connection cables often suffer insulation
damage. Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinks resulting from incorrect attachment or laying of
the connection cable.
• Cuts resulting from running over the connecting cable.
• Insulation damage resulting from forcefully pulling out
of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely
hazardous.
Check electrical connection cables regularly for dam-
age. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the regu-
lations VDE and DIN. Only use cables marked "HO 7
RNF". This is a binding regulation.
Il faut veiller à ce que toutes les tables et tous les rou-
leaux ne présentent aucune trace de résine.
Des rouleaux sales doivent être nettoyés.
Pour éviter l’échauffement du moteur, contrôler réguliè-
rement si les ouvertures d’air sont libres de poussière.
Après une utilisation prolongée, il est recommandé de
faire inspectionner la machine par un service d’entre-
tien agrée.
Entretien des outils:
Enlever régulièrement la résine de l’arbre de rabotage,
des dispositifs de serrage, des supports de lames et
des lames. Un outil net améliore la qualité de coupe.
Pour enlever la résine, les outils peuvent être immer-
sés dans un agent de commerce approprié pendant
24 heures.
Les outils en aluminium doivent être traités uniquement
avec un agent liquide, doux à ce type de métal.
Attention:
Avec une mauvaise condition du réseau électrique, la
puissance peut décliner pendant peu de temps. Consul-
ter un électricien.
m Branchement électrique
Le moteur électrique installé est raccordé en ordre de
marche. Le raccord correspond aux normes allemandes
VDE et DIN en vigueur.
Le raccordement électrique que doit effectuer le client
ainsi que les câbles de rallonge utilisés doivent aussi
correspondre à ces normes.
Les branchements et réparations de l’équipement élec-
trique ne doivent être effectués que par un spécialiste
de l’électricité.
Avis importants:
Le moteur électrique a été construit pour le mode d’em-
ploi S1.
Câbles de branchement électrique défectueux:
Il arrive fréquemment que l’isolation des câbles de bran-
chement électrique présente des avaries. Les causes
en sont:
• Ecrasements, si le câble passe sous la porte ou la
fenêtre.
• Coudes dûs à une mauvaise xation ou un mauvais
guidage du câble de branchement.
• Coupures dues à un écrasement du câble.
• Extractions violentes du câble de la prise murale.
• Fissures due au vieillissement de l'isolation.
Il est déconseillé d’utiliser des câbles électriques qui
présentent ces types d’avaries. Danger de mort.
Vérier régulièrement les câbles de branchement élec-
trique. Veiller à ce que le câble n’entre pas en contact
avec la tension de secteur pendant la vérication.
Les câbles de branchement électrique doivent corres-
pondre aux normes VDE et DIN en vigueur. Utiliser des
câbles marqués «HO 7 RNF».
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HT1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HT1050 in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info