782092

Scheppach HT1050 Manual

25
Zoom out
Zoom in
Previous page
1/108
Next page
25
the knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
must be tightened (8.4 N/m).
Please mind:
• Sharp planer/thicknesser knives guarantee a clean
planing surface and put less stress on the motor.
• Observe all knifes to have the same width (unbalance),
when nish-grinding. The minimum width of the knifes
is 20mm.
• The planer/thicknesser blades used on this machine
are not suitable for rebating and dovetailing.
• Finally lower the cutter block guard again onto the
table. Cover the cutter block and block it with the star
grip screw.
Installation
• Make sure there is sufcient space for handling the
work piece over the whole length without the operator
(or another person) having to stand in line with the
work piece.
• Using bolts, washers and hexagon nuts (not supplied
with the machine), the planer/thicknesser can be
bolted to a work bench.
• The planing machine must be bolted onto a rm, level
surface.
• The machine may not tilt, and the table must be
aligned.
Machine setting up and functions
The electric planer/thicknesser is transportable. It is
powered by a single-phase motor and is double insu-
lated. It has been designed for planing wood, and it
features a rational construction, easy operation, and
high efciency.
Maintenance
Always pull the power supply plug before doing any
servicing work. Having nished the work, put the
cutter block guard in operating position again.
Machine care
The planer/thicknesser requires little maintenance. The
ball bearings are permanently lubricated. After approx.
ten operating hours, lubrication of the following parts
is re commended:
• Bearing of the infeed and output roller
• Bearing of pulley and sprocket
• Greasing the chain.
The threaded spindle for height-adjustment of the thick-
nessing table may only be treated with a dry lubricant
agent.
• La lame a la position correcte si la règle est avancée
par les lames pas plus de 3 mm.
• Ensuite, reserrer toutes les vis fermément (8,4 N/m).
Faire attention:
• Ne travaillez qu'avec des lames bien affûtées. Elles
déchargent le moteur et garantissent une surface
lisse.
• Lors du repassage, veiller à ce que toutes les lames
aient la même largeur (charge déséquilibrée). La
largeur minimale des lames est de 20 mm.
• Les lames usées sur cette machine ne sont pas
appropriées à entailler en queue d’aronde.
• Finalement abaisser la protection de l'arbre de
rabotage sur la table, couvrir l'arbre et le serrer avec
la vis poignée-étoile.
Installation
• Vérier qu’il y ait de la place sufsante pour guider le
bois sur toute sa longueur, sans qu’une personne doit
se trouver dans une ligne avec la pièce à travailler.
• La rabo-dégau peut être xée sur un établi à l’aide de
boulons, rondelles et écrous hexagonaux (non livrés).
• La rabo-dégau doit être vissée fermément à une
surface solide et lisse.
• La machine ne doit pas basculer, et les tables doivent
s'aligner.
Construction et fonctions de la machine
La rabo-dégau peut être transportée. Elle est actionnée
par un moteur monophasé et a une isolation double.
Elle a été conçue pour travailler le bois. Sa construction
est rationnelle et de haute efcacité, et elle est facile-
ment maniable.
Entretien
Lors de toute opération d’entretien et de net-
toyage, arrêter le moteur et débrancher la prise
d’alimentation. Une fois les travaux achevés, tous
les dispositifs de protection doivent être remontés
immédiatement.
Entretien de la machine:
La rabo-dégau exige peu d’entretien. Les paliers sont
graissés à vie. Après 10 heures de service, il est recom-
mandé de huiler les paliers suivants:
• Paliers des rouleaux d'avance et de sortie
• Paliers de la poulie et de la roue dentée
• Graissage de la chaîne.
La broche letée pour le réglage en hauteur de la table
de rabotage doit uniquement être traitée avec un lubri-
ant sec.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HT1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HT1050 in the language / languages: English, German, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info