Manual Scheppach HRS800 (page 20 of 108) (English, German, French, Italian)

781640

Zoom out

Zoom in

1/108

20 GB

–Damaged switches must be replaced at a cus-

tomer service workshop.

–Do not use any faulty or damaged connection

cables.

–Do not use any electric tool on which the switch

cannot be switched on and off.

17 Attention!

–The use of other insertion tools and other ac-

cessories can entail a risk of injury.

18 Have your electric tool repaired by a qualied

electrician

–This electric tool conforms to the applicable

safety regulations. Repairs may only be per-

formed by an electrician using original spare

parts. Otherwise accidents can occur.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair active

or passive medical implants under certain conditions.

In order to prevent the risk of serious or deadly injuries,

we recommend that persons with medical implants

consult with their physician and the manufacturer of the

medical implant prior to operating the electric tool.

Additional safety rules for the electric cable hoist

Read this manual carefully - familiarise yourself with

this device. Observe the instructions for use, restric-

tions and possible dangers that apply to this device.

m DANGER! Risk of injury! Improper use of the ca-

ble hoist and non-compliance with the safety instruc-

tions can result in electric shock, re and/or serious

injuries.

• Do not lift or lower loads when persons are in the

danger area.

• Before putting the cable hoist into operation, check

the function of the brake, the operating and emer-

gency stop switch as well as the function of the safety

switches for the upper and lower limit every day.

• Before connecting to the power supply, make sure

that all control devices are in neutral or idle position.

• Do not use the cable hoist if the load to be moved

is exposed to a wind effect that endangers opera-

tional safety.

• Observe the load and the load-bearing equipment.

• Do not move the load attached to the load-bear-

ing attachment until the load stop is no longer in

the danger zone and an instruction for moving the

load is issued.

• Always stay in the area of the control unit and out-

side the danger zone as long as a load is suspend-

ed from the hook.

• Do not move a load that exceeds the load capacity

of the cable hoist or its attachment.

• Never disable the safety devices. Do not routinely

use the emergency stop switch to stop the load.

• When storing goods, maintain a safety distance of

at least 0.5 m between the moving parts and the

stored goods.

• Do not transport persons with the cable hoist.

• Do not tear off any stuck loads.

• Do not pull a load at an angle or drag it over the ground.

• Do not move vehicles with the load or the load-

bearing equipment.

• Avoid sudden and abrupt working movements.

• Ensure that the operating personnel are given the

necessary instructions.

• Always work in accordance with the operating in-

structions.

• Initiate the load movement at the lowest available

speed. Slowly tension the steel cable before mov-

ing the load. The steel cable must not be slack at

the beginning of the load movement.

• Do not give the motor short pulses with the control

unit to lower or lift the load.

• Wear a helmet when operating the cable hoist.

• Make sure that at least two windings of the steel

cable always remain on the cable drum. This en-

sures that the load is lifted safely.

m WARNING! Risk of electric shock! Incorrect han-

dling, incorrect electrical installation or excessive

mains voltage can lead to electric shock.

• Only connect the cable hoist if the mains voltage

of the socket corresponds to the information on

the type plate.

• Only connect the cable hoist to an easily acces-

sible socket so that you can quickly disconnect it

from the mains in the event of a fault.

• Do not operate the cable hoist if it is visibly dam-

aged or if the mains cable or plug is defective.

• If the power cord of the cable hoist is damaged, it

must be replaced by the manufacturer, their ser-

vice department or a similarly qualied person.

• Do not open the housing, but leave the repair to

specialists. To do this, contact a specialist work-

shop. In the event of repairs carried out indepen-

dently, improper connection or incorrect operation,

liability and warranty claims are excluded.

• Only parts that correspond to the original device da-

ta may be used for repairs. This cable hoist contains

electrical and mechanical parts which are indispen-

sable for protection against sources of danger.

• Do not operate the cable hoist with an external

timer or a separate remote control system.

• Do not immerse the cable hoist, power cord or plug

in water or other liquids.

• Never touch the power plug with wet hands.

• Never unplug the power cord from the wall outlet

by pulling on the cord, but always by taking hold

of the power plug.

• Keep the cable hoist, power plug and power cord

away from open re and hot surfaces.

• Route the power cord so that it does not become

a trip hazard or an obstacle.

• Do not bend the power cord or place it over sharp

edges.

• Only use the cable hoist indoors and never oper-

ate it in damp rooms or in the rain.

• If you are not using the cable hoist, if you are clean-

ing it or if a fault occurs, always switch off the cable

hoist and remove the mains plug from the socket

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HRS800 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2.75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HRS800 Manual

Product: