781495
27
Zoom out
Zoom in
Previous page
1/160
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
| 27
9.1.2 Surface planing mode (g. 20/21)
Attention! Watch out the right mounting of the
chip extractor (point 8.5)
(Narrow workpieces see g. 21) Open the knurled
srcew (10) and slide the planer blade cover (9) as
far as the width of the workpiece requires. Then
tighten the knurled srcew (10) again.
(Width, at workpieces see g. 20) Open the star
knob nut (4) and set the planer blade cover com-

The planer blade cover (9) covers the entire blade
roller! Tighten the star knob nut (4) again.
Plug in the machines power cord ( Press the green


table (14). Slide the workpiece as far as possible
with the push stick (16) forwards towards the plan-
ing table (7) over the knives (25).
  󰀨-
         


planing table (7) and knife block after the machine
has reached a complete standstill.

and cover the entire length of the planing knife.
9.2 Thicknessing
m IMPORTANT!: Pull out the power plug before

work.
9.2.1 Adjustment (g. 22)
Place the crank handle (12) on the spindle and
turn it to adjust the thicknessing table (21) to the
󰀨
scale (G).
-
ble (21) from bottom to top, i.e. crank the table fur-

Then crank the table (21) upwards to the desired
height.
9.2.2 Thicknessing mode (g. 22)
        

Plug in the machines power cord. Press the green

Place a workpiece on the thicknessing table (21).
Guide the workpiece towards the feed table (14).
  󰀨-
         


table (21) and knife block after the machine has
reached a complete standstill.
• m WARNING!   
maintenance~ or repair work, disconnect the pow-

-

-
imum of 1.1 mm out of the knife block.
   -


Never cut concavities, tenons or shapes.


-

m IMPORTANT!: The surfacing and thicknessing

         -
pose. The contact surface of the workpiece must be


place (e.g. using the thread in the machine base).


󰀨
machine.
        
     

time, the overload switch (1) can be reset again.
To work on long workpieces, use roller tables or
a similar supporting arrangement. Such optional

     
plane. Their height must be adjusted such that the
workpiece is horizontal when it is fed into and out
of the machine.
9.1 Surfacing
m IMPORTANT!: Pull out the power plug before

work.
9.1.1 Adjustment (g. 20+21)
Turn the adjustment knob for cutting depth (13)
to set the height of the feed table. The set cutting
󰀨
Loosen the parallel stop (8) with the clamping crew
(8a). Adjust the desired angle. The adjusted angle
󰀨
with the clamping screw (8a) after adjustment.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HMS1080 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HMS1080 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 6.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info