781495
26
Zoom out
Zoom in
Previous page
1/160
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
26 |
Anti-kick claws (g. 9 - pos. 20)




(25) fall back without hindrance due to their own

Planing blades (g. 17 - pos. 25)
-

The machine may only be used if all these condi-
tions are satised.


-
dition for machining short workpieces.

Check that the stop is secure before starting the ma-
chining work.
        
times. Stand to the side of the machine.
        
a safe distance from the cutting block and from the
point at which the chips are discharged.
Do not start the planing work until the cutting block
has reached the required speed.


wood which has lots of knots or knot holes.
Secure long workpieces to prevent them tipping over




󰀨
the mains plug and remove the jammed workpiece.
Set the smallest cutting size after use to prevent the

m CAUTION!
-
top using suitable screws / screw clamps since oth-
erwise there is a risk that it will tip over.
       

are identical to the mains data.
8.4 Crank handle for thickness planer chip depth
(g. 8)

spindle.
8.5 Chip extraction (g. 10)


parts (5, 5a) together and retighten the Phillips
screw.
8.6 Chip extractor - surface planing (g. 11+12)
Set the planing knife cover cpl. (9) in the upperst
position.
-
ing table (21) in the lowest position.

         


pins (3) outwards.

pins in the table. Attention! The machine won´t start

     
down again.
8.7 Chip extractor - thickness planing
(g. 13+14)
The parallel stop (8) needs to be removed for thick-




pins in the table. Attention! The machine won´t start

9. Installation
m IMPORTANT!
You must fully assemble the appliance before
using it for the rst time!
Before each use, check the following:
󰀨 

Locked disconnected protective equipment
(g 1a - pos. 3)

󰀨
checking that the machine cannot be turned on
whenever the protective equipment is open
Brake
Switch on the machine at the start of work and
allow the machine to reach speed. Now switch the
󰀨
standstill within 10 seconds. Otherwise, there is a
defect.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HMS1080 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HMS1080 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 6.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info