644509
31
Zoom out
Zoom in
Previous page
1/157
Next page
Documentation
9322 0311 Page:31
Planing – planing shaft protection
Fig.„I„
While planing up to 75mm workpiece thickness, the planing
shaft protection has to cover from above the workpiece and
the planing shaft. At a workpiece width of more than 75mm,
adjust the check rail of the planing shaft protection up to the
width of workpiece. Pay attention to put your hands on the
workpiece with adjacent thumbs.
1 trimming stopper
2 planing shaft protection
Joining
Fig. „J„
Use for this working cycle the trimming stopper, let the
planing shaft protection rest on the trimming desk and adjust
the check rail up to the width of workpiece.
Press the workpiece against the planing stopper and lead it
now with both hands over the planing shaft. As soon as the
board reaches far enough into the removal desk, place your
hand on it and push it without a halt over the knife shaft.
Planing – particle ejection
Fig. ‘‘K“
While planing the trimming desk has to be locked.
Plug on the exhaust line onto the exhaust hood.
In connection with an exhaust device then can be sucked off.
Diameter of the exhaust standpipe 100mm
Thickness planing – machine adjustment
Pull up the desk locking device and swing open the trimming
desk.
Position the height adjustment at the trimming desk to full
height.
Swing up and lock the ejection hood (arrow).
Plug on the exhaust standpipe and tighten the wing nut.
In connection with an exhaust device then can be sucked off.
Always pay attention to, that the limit switch unit is free of dirt
and particles.
Thickness planing – desk adjustment
Fig. ‘‘L1“
The height of the thickness desk is adjustable by means of
the hand wheel.
The integrated display of the position shows the passage
height of 5-180 mm (hms/hmc3200ci) and 3-140 mm
(hmc2600ci/hms260ci).
One hand wheel turn corresponds to 2 mm.
Keep the thickness desk and the trimming desks always free
of resin.
Clamping thickness max. 5 mm. (hms/hmc3200ci,
hmc2600ci) and 3 mm (hms260ci)
The graduation marks of the scale ring make possible a
fine adjustment, at which 1graduation mark corresponds
to 0, 05 mm (hms/hmc3200ci/hmc2600ci) and 0,057 mm
(hms260ci).
Scale correction
The thickness scale can be corrected at measuring inaccuracy.
Example: (hms/hmc3200ci, hmc2600ci)
The passage height is adjusted to 100 mm.
The processed workpiece has a measure of 101 mm.
Loosen the mounting screws of the thickness scale.
Adjust the thickness scale to the measure 101 mm.
Tighten the mounting screws of the thickness scale.
Keep the thickness desk and the trimming desks always free of
resin.
Thickness planing - feed
Fig. ‘‘M“
The feed can be switched on and off with the lever (1).
0 = OFF
1 = ON
First switch on the feed, then set-in the workpiece.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach hmc 3200 ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach hmc 3200 ci in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach hmc 3200 ci

Scheppach hmc 3200 ci Additional guide - All languages - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info