644509

Scheppach hmc 3200 ci Manual

30
Zoom out
Zoom in
Previous page
1/157
Next page
Documentation
9322 0311
Page:30
Setup and adjustment
Fig. “A”
The machine stands on 4 adjustable rubber block supports.
Level unevenness of the floor. Loosen the lower hexagonal
nuts by means of the wrench and screw in or out the rubber
block supports.
Tighten the hexagonal nuts again. (check)
Attention!
It is obligatory to adjust the machine by means of a water
level.
In the case of removed rubber block supports the machine
can be bolted to the floor through the boreholes.
Surface planing fence
Fig.:“C”
Setting the surface planing fence onto the machine
Find the 90° position with the aid of a back square
Pull the lock lever 1 tight.
Set fence screws 2 to the 90° and 45° position using a 10
span single-head wrench.
The surface planing fence can be swung to any position
between 90° - 45°, when the handles on the swinging
segments are loosened.
Set the 90° position with a back square. After setting each
angle, check the exactness of the measurement on a trial
piece using a protractor.
Driving mechanism
Fig. „B„
Lift the machine according to the sign-board for to swing in
and out the wheel set.
Assembly
The scope of delivery contains:
1 hook spannerl 52/55 Scope of delivery doesn’t contain:
1 hexagonal spanner SW 3 1 fork wrench SW 13
1 hexagonal spanner SW 5
1 fork wrench SW 8
Due to technical reasons of packaging, your scheppach planing machine is not completely assembled.
Do not lift the planing machine at the trimming desks!
With the chip ejection hood retracted, the thicknessing table may be moved up to a maximum of 75 mm only!
Fig.:„D“
The clamping of the trimming stopper is effected by means of
an eccentric lever (1)
Additionally the trimming stopper can be clamped with the
lever (2)
(hms/hmc3200ci / hmc2600ci)
The trimming stopper is adjustable 320 mm (hms/
hmc3200ci) and 260 mm (hmc2600ci/hms260ci) across the
planing width.
Attention!
The trimming stopper has to be fixed always safely.
Screw on the planing shaft protection at the trimming desk,
which lets down.
The planing shaft protection can be swivelled apart without
use of a tool by pulling up the eccentric lever, swivel apart
the planing shaft protection, push down the eccentric
lever again.
Fig. “E„
Attention:
While planing never work without planing shaft protection.
Adjustment of the trimming stopper
Fig.:„C1“
Check 90°/45° angle and adjust by means of the cylindrical
screw M4x8.
1 = adjusting screw 90° angle
2 = adjusting screw 45° angle
Pay attention to the topic „Putting into operation” fig.: „H„,
„I„, „J„
Attention!
The trimming stopper has to be always fixed safely.
Putting into operation
Before putting into operation pay attention to the security
instructions.
All protection and auxiliary equipment have to be
assembled.
Carry out adaptation, adjustment, measuring and cleaning
work only with switched off motor.
Pull power plug!
Planing – chip off particles
Abb. „H“
The chip off particles while planing is infinitely adjustable by
the articulated lever 1 from 0-5 mm (hms/hmc 3200ci) and
from 0-3 mm (hmc2600ci/hms260ci).
At the planing and at the attachment, the thickness desk
has to be adjusted between 70 mm - 140 mm (hmc2600ci/
hms260ci) and 70 mm - 180 mm (hms/hmc3200ci).
Attention, else the exhaust hood will be clamped! Fig:. „H1„
In the case of longer workpieces (longer than charging desk
or removal desk) a roller stand (special accessories) or similar
has to be used.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach hmc 3200 ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach hmc 3200 ci in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach hmc 3200 ci

Scheppach hmc 3200 ci Additional guide - All languages - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info