644509

Scheppach hmc 3200 ci Manual

29
Zoom out
Zoom in
Previous page
1/157
Next page
Documentation
9322 0311 Page:29
Electrical connection
Fig. “F”
Connect the machine to the mains with a CEE plug, the supply line must be protected with 16 A.
Switch main switch to the CEE plug in the I position
On the operating switch, press the green on-switch; the planing block starts to run.
Push the red mushroom-shaped button to shut down, planing block is braked within 10 sec.
When shutting down the planing block at the main switch (CEE plug), the braking function is ineffective!
The main switch is in the 0 position, the motor is free of current.
When connecting to the mains or changing the position, the rotational direction must be checked and when
necessary the polarity switched using a screwdriver (machine socket).
The electric motor installed is connected and ready for operation. The connection corresponds to the relevant VDE and DIN
regulations. Connection to the mains by the customer and the extension cable used must correspond to these regulations.
Motor braking device
When shutting the machine down, an automatically effective regenerative brake is safely applied. The brakes brake the
driving motor of the planing block within 10 sec. The electric brake system is interrupted after max. 14 seconds. If the
braking procedure lasts longer than 14 seconds, the machine may no longer be operated, since the brakes are defective. It is
imperative that the machine is cut off from the source of power. Only professional electricians may be used to clear errors.
Operating mode / Working time
The electric motor is dimensioned for operating mode S 6 - 40 %.
S 6 = Continuous operation duty type
40 % = Referring to 10 min.: 4 min. load; 6 min. disengaged
When the motor is overloaded, it turns itself off by using a winding thermostat that is built into the motor windings. After a
cooling period (of varying length), the motor can be switched on again.
Damaged electrical connection cables
Insulation damage often arises on electrical connection cables.
Possible causes:
Pressure points, when connection cables are led through windows or door frames.
Kinks due to improper fastening or guides for the connection cable.
Cuts caused by the connection cable being driven over.
Insulation damage arising from cable being ripped out of the wall socket.
Tears due to aging of the insulation. Such faulty electrical connection cables should no longer be used, as the damage to
the isolation renders them l i f e - t h r e a t e n i n g.
Regularly check electrical connection cables for damage. Make sure that the cable is not connected to the mains while
checking. Electrical connection cables must correspond to the relevant VDE and DIN and the local EVE regulations. Only
use connection cables with the identification number H 07 RN. It is mandatory for the type designation to be printed on
the connection cable.
Extension cables must exhibit a cross section of 1.5 square millimeters (up to 25 m length), and 2.5 square millimeters
(over 25 m length).
The mains connection is protected with 16 A (anti-surge).
Three-phase current motor
Supply voltage must be 380 - 420 V 50 Hz.
Mains connection and extension cable must have five wires = 3 P + N + SL.
Extension cables must have a minimum cross section of 1.5 mm².
The mains connection is protected with a maximum of 16 A.
When connecting to the mains or changing the position, the rotational direction must be checked and the polarity
switched where necessary.
Connection and repairs of electrical equipment may only be carried out by qualified professionals.
In the case of inquiries, please quote the following data:
Motor manufacturer; motor model
The motor‘s type of current
Data of the machine‘s type plate
Data of the electronic control system
If returning the motor, always send the complete drive unit with electronic control system.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach hmc 3200 ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach hmc 3200 ci in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach hmc 3200 ci

Scheppach hmc 3200 ci Additional guide - All languages - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info