Manual Scheppach HM80L (page 28 of 228) (All languages)

781434

Zoom out

Zoom in

1/228

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

28 | GB

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (27a) must be xed at the

outer position.

• Open the locking lever (27b) for the adjustable stop

rail (27a) and push the adjustable stop (27a) rail

outwards.

• The adjustable stop rail (27a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (27a) and the saw

blade (5) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (27a)

and the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to its upper position.

• Release the rotary table (9) by loosening the set

screw (21).

• Using the handle (2), set the rotary table (9) to the

desired angle (refer also to point “Cross cut 90°

and turntable 0° - 45°” in this regard).

• Re-tighten the set screw (21) in order to secure

the rotary table.

• Undo the locking screw (23)

• Use the handle (2) to tilt the machine head to the

left until it coincides with the required angle value

(in this connection see also section “Mitre cut 0°-

45°”).

• Re-tighten the xing screw (23).

• Cut as described under section “Cross cut 90°

and turntable 0°”.

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing

the lock (3 - Fig. 1); in the process, raise the saw

blade guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (At-

tention: left-handed thread).

• Remove the screw (28) and saw blade ange (29).

• Carefully remove the saw blade (risk of injury from

the saw blade teeth).

• Place a new saw blade on the inner saw blade

ange. In the process, observe the rotational di-

rection of the saw blade.

• Fit the outer saw blade ange and rmly tighten

the screw.

• Move the saw blade guard back to the correct po-

sition.

Replacing laser batteries (Fig. 6)

• Remove the laser battery cover (30). Remove the

2 batteries.

• Replace both batteries with the same or an equiva-

lent type. Make sure that they are inserted with the

same polarity as the used batteries.

• Close the battery cover.

Attention! For bevel cuts (inclined saw head), the

moveable stop rail (27a) must be xed in the inner

position.

• Open the set screw (27b) on the moveable stop rail

(27a) and push the moveable stop rail (27a) out-

wards.

• The moveable stop rail (27a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (27a) and the saw

blade (5) is no more than 8 mm.

• Before making the cut, check that no collision could

occur between the stop rail (27a) and the saw blade

(5).

• Tighten the set screw (27b) again.

• Loosen set screw (21).

• Use the handle (2) to set the turntable (9) to the de-

sired angle. The pointer on the turntable must co-

incide with the desired angular extent of the scale

on the base (7).

• Re-tighten the locking screw (21) to x the turntable

(9).

• Cut as described under section „Cross cut 90° and

turntable 0°“.

Mitre cut 0°- 45° (Fig. 1, 1.3)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (27a) must be xed at the

outer position.

• Open the set screw (27b) for the adjustable stop

rail (27a) with an Allen key and push the adjustable

stop rail outwards.

• The adjustable stop rail (27a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (27a) and the saw

blade (5) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (27a)

and the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to the top position.

• Fix the rotary table (9) in the 0° position.

• Loosen the set screw (23) and use the handle (2) to

angle the machine head to the left, until the pointer

(25) indicates the desired angle measurement on

the scale (24).

• Re-tighten the xing screw (23).

• Cut as described under section „Cross cut 90° and

turntable 0°“.

Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 1, 2, 1.3)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the

right in relation to the stop rail (double mitre cut).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM80L in the language / languages: All languages as an attachment in your email.

The manual is 11.77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HM80L Manual

Product: