Manual Scheppach HM80L (page 26 of 228) (All languages)

781434

Zoom out

Zoom in

1/228

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 | GB

The positioning of the machine must provide for at

least 80 cm of clearance in all directions and in or-

der to allow for cleaning and repair work as well as

necessary adjustments in observance of safety con-

ditions and with sufcient room to manoeuvre.

CAUTION: Position the machine in a zone which is

suitable in respect to the environmental conditions

and lighting. Never forget that the general environ-

mental conditions play an extremely important role in

accident prevention.

CONNECTION TO THE POWER SUPPLY

Make sure that the socket is in a good condition. We

would like to remind you that the power supply must

be connected to a magnetic-thermal circuit breaker

which protects all lines from short-circuits and over-

9. Assembly

WARNING! For you own safety, only insert the

mains plug in an outlet when all assembly steps

have been completed and you have read and un-

derstood the safety and operating instructions.

Lift the saw out of the packaging and place it on your

work bench. (Positioning of the saw on the work

bench - see the next page under „POSITIONING /

WORK STATION“)

Installation of the dust bag

• Squeeze together the metal ring on the dust bag

(12) and attach it to the outlet opening in the motor

area.

Emptying the dust bag

• By pressing the metal ring wings of the dust bag

(12) together the dust bag can be disengaged from

the outlet opening.

• Open the zipper of the dust bag and shake the

contents into a dustbin.

• Close the zipper and install the dust bag on the

machine again as described.

Assembling the work piece clamping device

(Fig. 1.1)

• Loosen the locking screw (17) and attach the work

piece clamping device (10) to the left or right of the

xed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports

(Fig. 1.1 – 1.2)

• Loosen the cross-head screw (14) and guide the

work piece support through the specied hole on

the side of the xed saw bench.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the ma-

chine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the op-

erating button may not be pressed when inserting

the plug in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal per-

formance.

• Hands may never enter the processing zone when

the machine is in operation.

• Release the handle button and switch off the ma-

chine prior to any operations.

8. Commissioning

Prior to commissioning, observe the safety in-

structions in the operating instructions.

REMOVAL FROM THE PACKAGING

Remove the machine from its package, which pro-

tects it during transport, without damaging the pack-

age in order to be able to use it later for transporting

the mitre saw for long-term storage.

MOVING

Since the mitre saw is relatively small and light, its

location can be easily changed, even by a single per-

son. After locking the locking knob (26 - Fig. 4) in the

bottom position, lift the mitre saw by the handle (34

- Fig. 4).

TRANSPORT

If the machine must be transported, carry it by the

handle (34 - Fig. 4) and place it in the original pack-

aging in which it was supplied. In the process, make

sure that it is correctly positioned in the package (see

arrows on the package).

If possible, the load should be xed with ropes or

securing belts in order to prevent shifting during the

transport or parts of the load from falling down.

POSITIONING/WORK STATION

Position the machine on a work bench or on a at

base so that the machine is supported as stably as

possible. Make sure that the machine is always se-

cured to a workbench or table if possible. Secure the

machine through the holes on the base (7) of the ma-

chine by using 4 screws on a workbench, an under-

carriage o. eg.

When working with the machine, ergonomic factors

must be considered; the ideal height of the work table

or the base is reached when the base surface or the

upper work surface is 90 to 95 cm above the ground.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM80L in the language / languages: All languages as an attachment in your email.

The manual is 11.77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HM80L Manual

Product: