781434

Scheppach HM80L Manual

25
Zoom out
Zoom in
Previous page
1/228
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 25
5. Do not mix old and new batteries or batteries
of different types or manufacturers! Replace an
entire set of batteries at the same time.
6. Immediately remove used batteries from the
device and dispose of them properly! Do not
dispose batteries with household waste. Defective
or used batteries must be recycled according to
Directive 2006/66 / EC. Give back batteries and
/ or the device has been offered to the collective
facilities. About disposal facilities you can inform
by your municipal or city government.
7. Do not allow batteries to heat up!
8. Do not weld or solder directly on batteries!
9. Do not dismantle batteries!
10. Do not allow batteries to deform!
11. Do not throw batteries into re!
12. Keep batteries out of the reach of children.
13. Do not allow children to replace batteries without
supervision!
14. Do not keep batteries near re, ovens or other
sources of heat. Do not use batteries in direct
sunlight or store them in vehicles in hot weather.
15. Keep unused batteries in the original packaging
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together!
This can lead to a short-circuit of the battery and
thus damage, burns or even the risk of re.
16. Remove batteries from the equipment when it will
not be used for an extended period of time, unless
it is for emergencies!
17. NEVER handle batteries that have leaked
without appropriate protection. If the leaked
uid comes into contact with your skin, the skin
in this area should be rinsed off under running
water immediately. Always prevent the uid from
coming into contact with the eyes and mouth.
In the event of contact, please seek immediate
medical attention.
18. Clean the battery contacts and corresponding
contacts in the device prior to inserting the
batteries.
7. Residual risks
The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions“ and the „Proper use“ are observed
along with the whole of the operating instructions.
6. Do not use any loose reducing rings or bushes for
the reducing of holes on saw blades.
7. Make sure that xed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
8. Make sure that xed reducer rings are parallel to
each other.
9. Handle insertion tool with caution. They are
ideally stored in the originally package or special
containers. Wear protective gloves in order to
improve grip and to further reduce the risk of
injury.
10. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from ac-
cidents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specied here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representa-
tive.
Safety instructions for handling batteries
1. Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated on
the battery.
2. Do not short-circuit batteries.
3. Do not charge non-rechargeable batteries.
4. Do not overcharge batteries!
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HM80L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM80L in the language / languages: All languages as an attachment in your email.

The manual is 11.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info