Manual Scheppach HL810 (page 21 of 92) (English, German, French, Italian)

781857

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

Stroke limit for short logs, Fig. 10

Lower splitting knife position about 10 cm above ta-

ble.

• Move splitting knife to the desired position

• Release one operating arm

• Switch motor off

• Release the second operating arm

• Undo the star grip screw (10a)

• Push the stroke set rod (8) to the top until it is

stopped by the spring

• Tighten the star grip screw (10a) again.

• Switch motor on

• Check upper position

Switching on and off (12)

Press the green button for switching on.

Press the red button for switching off.

Note: Check the function of the ON/OFF unit before

every use by switching on and off once.

Restarting safety in case of current interruption

(no-volt release).

In case of current failure, inadvertent pulling of the

plug, or a defective fuse, the machine is switched off

automatically.

For switching on again, press anew the green button

of the switch unit.

Splitting

• Place the log on the table, hold it with both handles,

press the handles down. As soon as the splitting

knife enters the wood, push the handles down and

to the outside at the same time. This prevents the

wood from putting pressure on the holder plates.

• Only split straight cut logs.

• Split the logs in vertical position.

• Never split in horizontal position or across.

• Wear protective gloves when splitting.

End of work

• Move the splitting knife to the lower position.

• Release one operating arm.

• Switch the machine off and pull the power plug.

• Close the venting cap.

• Observe the general maintenance instructions.

Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

10. Initial operation

Make sure the machine is completely and expertly as-

sembled. Check before every use:

• The connection cables for any defective spots

(cracks, cuts etc.).

• The machine for any possible damage.

• 

• The hydraulic system for leakage.

• The oil level.

Checking the oil level (Fig. 13)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage the

oil pump. The correct oil level is approx. 10 to 20 mm

below the oil tank surface.

Note: The level of oil must be checked when the riving

knife is pulled back. If the oil level is at the lower notch,

then the oil level is at a minimum. Should this be the

case, oil must be immediately added. The upper notch

indicates the maximum oil level. The machine must

be on level ground. Screw in the oil dipstick fully, to

measure the oil level.

Functional test

Test the function before every use.

Action: Result:

Push both handles towards

below.

Splitting knife goes

down to approx. 10

cm above the table.

Let one handle loose, then

the other.

Splitting knife stops

in the desired po-

sition.

Let both handles loose. Splitting knife

returns to upper

position.

Check the oil level before every use – see chapter

“Maintenance“.

Venting, Fig. 14

Before working with the log splitter, vent the hydraulic

system.

• Release the venting cap 6 by a few revolutions so

the air can escape from the oil tank.

• Leave the cap open during the operation.

• Before you move the log splitter, close the cap

again in order not to lose any oil.

If the hydraulic system is not vented, the enclosed air

will damage the gaskets and with it the complete log

splitter.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL810 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3.75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL810 Manual

Product: