Manual Scheppach HL730 (page 23 of 136) (English, German, French, Italian, Polish, Swedish, Norwegian)

781852

Zoom out

Zoom in

1/136

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

When connecting to the mains or relocating the ma-

chine, check the direction of rotation (swap polarity in

the wall socket if necessary).

Turn pole inverter in the machine socket.

11. Cleaning

Attention!

Pull out the power plug before carrying out any clean-

ing work on the equipment.

We recommend that you clean the equipment imme-

diately after you use it.

Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

12. Transport

For transport, the splitting knife A must be complete-

ly moved down. Slightly tilt the log splitter with handle

B on the splitting column until the machine is inclined



13. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and



Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

14. Maintenance

Attention!

Pull out the power plug before carrying out any main-

tenance work on the equipment.

When must the oil be changed?

First oil change after 50 operating hours, then every

500 operating hours.

Oil change (g. 12)

• Completely retract the splitting column.

• Put a container with a volume of at least 6 litres

under the splitter.

• Release the oil dipstick 14.

• Open the oil drain plug 12a under the oil tank so the



Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H07RN“.

The printing of the type designation on the connec-

tion cable is mandatory.

For single-phase AC motors, we recommend a fuse

rating of 16A (C) or 16A (K) for machines with a high

starting current (starting from 3000 watts)!

AC motor 230 V/ 50 Hz

Mains voltage 230 Volt / 50 Hz.

Mains voltage and extension cables must be 3-lead

= P + N + SL. - (1/N/PE).

Extension cables must have a minimum cross-sec-

tion of 1.5 mm².

Mains fuse protection is 16 A maximum.

Three-phase motor 400 V / 50 Hz

Mains voltage 400 V / 50 Hz

Mains voltage and extension cables must be 5-lead

(3P + N + SL (3/N/PE).

Extension cables must have a minimum cross-sec-

tion of 1.5 mm².

Mains fuse protection is 16 A maximum.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL730 in the language / languages: English, German, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 5.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL730 Manual

Product: