781852
22
Zoom out
Zoom in
Previous page
1/136
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 | GB
Venting (g. 14)
Before working with the log splitter, vent the hydraulic
system.
Release the venting cap 14 by a few revolutions so
the air can escape from the oil tank.
Leave the cap open during the operation.
Before you move the log splitter, close the cap
again in order not to lose any oil.
If the hydraulic system is not vented, the enclosed air
will damage the gaskets and with it the complete log
splitter.
Stroke limit for short logs (g. 14)
Lower splitting knife position about 10 cm above ta-
ble.
Move splitting knife to the desired position
Release one operating arm
󰀨
Release the second operating arm
Undo the star grip screw (10a)
Push the stroke set rod (8) to the top until it is
stopped by the spring
Tighten the star grip screw (10a) again.
Switch motor on
Check upper position
Switching on and o󰀨 (12)
Press the green button for switching on.
󰀨
Note: Check the function of the ON/OFF unit before
󰀨
Restarting safety in case of current interruption
(no-volt release).
In case of current failure, inadvertent pulling of the
󰀨
automatically.
For switching on again, press anew the green button
of the switch unit.
Splitting
Place the log on the table, hold it with both handles,
press the handles down. As soon as the splitting
knife enters the wood, push the handles down and
to the outside at the same time. This prevents the
wood from putting pressure on the holder plates.
Only split straight cut logs.
Split the logs in vertical position.
Never split in horizontal position or across.
Wear protective gloves when splitting.
End of work
Move the splitting knife to the lower position.
Release one operating arm.
󰀨
Close the venting cap.
Observe the general maintenance instructions.
9.4 Fitting the claws (enclosed accessories
bag C)
Fasten the additional retainers (D) to the claws with

Make sure that the larger additional retainer is
fastened with the left claw (4).
Place the adjustable claws on the hexagon nuts
previously attached, and fasten these with the star

Note that the prongs on the claws must point

m IMPORTANT!
You must fully assemble the appliance before using it

10. Initial operation
Make sure the machine is completely and expertly
assembled. Check before every use:
The connection cables for any defective spots
(cracks, cuts etc.).
The machine for any possible damage.

The hydraulic system for leakage.
The oil level.
Checking the oil level (g. 13)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage
the oil pump. The correct oil level is approx. 10 to 20
mm below the oil tank surface.
Note: The level of oil must be checked when the riv-
ing knife is pulled back. If the oil level is at the low-
er notch, then the oil level is at a minimum. Should
this be the case, oil must be immediately added. The
upper notch indicates the maximum oil level. The
machine must be on level ground. Screw in the oil
dipstick fully, to measure the oil level.
Functional test
Test the function before every use.
Action: Result:
Push both handles towards
below.
Splitting knife goes
down to approx. 10
cm above the table.
Let one handle loose, then
the other.
Splitting knife stops
in the desired po-
sition.
Let both handles loose. Splitting knife
returns to upper
position.
Check the oil level before every use see chap-
ter “Maintenance“.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HL730 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL730 in the language / languages: English, German, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 5.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info