Manual Scheppach FS850 (page 24 of 92) (English, German, French, Polish)

781905

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

Caution: Cutting disc must always be cooled with

water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at

the sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an acces-

sory to achieve the performance of a bigger Indus-

trial machine. It does a better job at the output for

which it is designed.

• Dene all machine settings only when it is switched

o󰀨.

• Do not leave the machine unattended as long as

it is running.

• During shut down, leave the machine only after it

comes to a complete standstill.

• Always switch the machine o󰀨 before pulling out

the power plug from the mains socket.

• Always pull out the power plug. Never disconnect

the power plug from the mains socket by pulling

at the cable.

• Do not use cutting discs that do not meet the size

specications.

• Do not carry the machine by the cable.

Do not work with the machine if you are not sure

whether a working condition is safe of unsafe.

90° cuts Fig.6-7

1. Loosen the wing bolt (C)

2. Set angled stop (6) to 90° and tighten the wing

bolt (C) again.

3. Tighten the wing bolt (D) to x the angled stop (6).

(Fig.6)

4. Push the machine head (1) towards the rear by

the handle (11).

5. Place the tile on the stop rail (7) at the angled stop

(6).

6. Switch the tile-cutting machine on. (Fig.7)

Caution: Wait for the cooling water to reach

the cutting disc (10).

7. Pull the machine head (1) slowly and uniformly by

the handle (11) in the forward direction through

the tile.

8. Switch the tile-cutter o󰀨 again after reaching the

end.

45° diagonal cut (Fig. 8)

1. Set the angled stop (6) to 45°

2. Perform cutting as described above.

45° longitudinal cut (Fig. 9)

1. Loosen the star knob screw (E) on both sides

2. Angle the guide rails (8) 45° to the left on the an-

gle scale (17).

3. Re-tighten the star knob screw (E) on both sides.

4. Perform cutting as described.

Residual risks can be minimized if the „safety in-

structions“ and the „proper use“, as well as operating

instructions manual are observed jointly.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the equip-

ment is used in commercial, trade or industrial busi-

nesses or for equivalent purposes.

Any use beyond the one specied will be treated

as improper. The manufacturer will not be liable for

damages resulting from such improper use; the risk

will be borne by the user alone.

10. Installation

m IMPORTANT!

You must fully assemble the appliance before

using it for the rst time!

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself

with its use and its restrictions, but also with the

specic potential risks.

• Check the machine carefully for damages to en-

sure that it is able to achieve the intended output.

In case of doubt, please replace the concerned

component.

• Ensure that the switch is on O󰀨, before inserting

the power plug into the mains socket.

• Ensure that the machine is cleaned and lubricat-

ed properly.

• Before start-up, check the machine for damaged

parts and nd out whether these parts are work-

ing properly and performing their dened function.

• Check the alignment of all moving parts, all bro-

ken or fastening parts, and all other conditions that

can a󰀨ect smooth operation. Each damaged part

should be repaired or replaced by a technician im-

mediately.

• Do not use the machine if a switch cannot be ac-

tivated/deactivated correctly.

On/O󰀨 switch (Fig. 4)

To switch on, press “I” on the On/O󰀨 switch (16) Be-

fore starting the cutting process, wait until the cutting

wheel reaches its maximum speed and the cooling

water pump (14) has fed the water to the cutting

wheel. To switch o󰀨, press the “0” on the switch (16).

(Fig. 4).

Operation

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches

the existing voltage; connect the power plug to the

mains power supply only thereafter

• The cutting disc should be free to run before the

machine is switched on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach FS850 in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 6.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach FS850 Manual

Product: