Manual Scheppach Forsa 8.0 (page 34 of 60) (English, German, Finnish)

782260

Zoom out

Zoom in

1/60

29 english

Maintenance

Switch off the motor and disconnect the power supply plug

before doing any maintence and cleaning work. Follow the

following maintenance procedures for your panel sizing circular

saw.

• Check belt tension after approx. 20 operating hour and

tighten if necessary. To do this open the right side cover.

Set required belt tension by adjusting the fastening nuts

on the motor equally.

• Spray the roller chain and moving parts (vertical and

swivel adjustment units) occasionally with dry lubricating

spray. Open the right side cover.

• Check the sliding table carriage guide unit for dirt and

clean if required.

• Always keep the table surface free of resin.

• If a dust extractor is not being used the saw blade

protective cover should be cleaned occassionally of any

wood residue and sawdust. This is important for ensuring

troublefree ejection of sawdust. If the machine is used

without a dust extractor sawdust accumulation could

reduce the vertical and angle adjustment range.

• Clean the sliding table carriage guide at regular intervals.

All safety equipment and protective devices must be reattached

as soon as repair and maintenance work has been completed.

• To ensure troublefree ejection of sawdust the saw blade

protective cover should be cleaned of any wood residue.

• The vertical and angle adjustment range could be reduced

if sawdust is allowed to accumulate. Open the protective

cover and clean the adjustment area.

Electrical Connection

The built in electric motor is wired ready for operation. The

connection conforms with the applicable VDE and DIN

regulations.

The mains connection on site and the extension cable used

should also comply with these regulations.

Motor Brake Device

Your panel sizing circular saw is equipped with an automatic

shutdown brake. The brake starts to take effect after the

driving motor switches off.

The saw blade must stop max.10 sec after switching off. Check

daily!

Do not operate the machine after a longer braking time.

Important Information

The 230 V / 50 Hz and 400 V / 50 Hz electric motors are

designed for S6 40 % operating mode.

If the motor starts to overload it switches off automatically. The

motor can reactivated after a cooling period (exact interval

differs).

Faulty Electric Connection Cables

Electric connection cables are frequently subjected to

insulation damage.

Insulation damage results from:

• Pinch points where connection cables are routed through

windows or door cracks.

• Kinks due to improper fastening or routing of connection

cables.

• Cuts caused by running over connection cords.

• Insulation damage caused by pulling the cable out of the

wall socket.

• Cracks due to aging.

Faulty or damaged electric connection cables are hazardous

and should not be used under any circumstances as fatal

injury could result.

Check electric connection cables regularly for damage.

Before you check the connection cable, make sure that it

has been completely disconnected from the power supply.

Electric connection cables must conform to the applicable

VDE and DIN regulations. Use only connection cables

marked as H 07 RN.

Regulations require that the type designation be printed on

the connection cable.

2-3mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 8.0 in the language / languages: English, German, Finnish as an attachment in your email.

The manual is 9.46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Forsa 8.0 Manual

Product: