782260

Scheppach Forsa 8.0 Manual

35
Zoom out
Zoom in
Previous page
1/60
Next page
english 30
Fault Possible Cause Remedy
saw blade detachs after motor is switched off fastening nut too slack tighten M 20 left-handed fastening nut
motor fails to start a) mains fuse outage a) check mains fuse
b) faulty extension cable b)
refer to section on electrical connection, in the
operating instructions
c) faulty connections to motor or switch, brake
fails to release c) should be checked by a qualified electrician
d) faulty motor or switch d)
see section on electrical connection, in the
operating instructions
e) saw blade protective cover open e) close saw blade protective cover
incorrect motor rotational direction a) faulty capacitor a) should be replaced by a qualified electrician
b) incorrect connection b) wall socket polarity should be changed by a
qualified electrician
no motor output, motor switches off automati-
cally a) overload caused by dull saw blade a) install sharpened saw blade
b) thermal protection activates b) can be switched on again after cooling
period
burn marks where cut is made
on cross section
a) dull saw blade a) install sharpened saw blade
b) incorrect saw blade b) install saw blade for lengthwise cuts
c) fence not parallel to saw blade c) replace fence
d) sliding table carriage not parallel to saw
blade d) align sliding table carriage to saw blade
reduced saw performance at full motor speed loose belt tighten belt, refer to maintenance section
workpiece jams between sawblade and fence fence does not run parallel to saw blade check fence alignment
sliding table carriage does not move a) lock has not been released a) release lock
b) guide unit is dirty b) clean guide unit
AC Motor
• The required supply voltage is 230 Volt - 50 Hz.
• Extension cables up to 25 m in length must have a cross
section of 1.5 mm2; extension cables which exceed 25
m in length must have a cross section of 2.5 mm2.
• The mains connection has a 16 A time delay fuse.
Three-Phase Current Motor
The 400 V / 50 Hz electric motor is designed for the S6 / 40 %
operating mode.
• The required supply voltage is 400 Volt - 50 Hz.
• The mains connection and extension cable must be
equipped with 5 wires = 3 P + N + PE.
• Extension cables must have a cross section of no less
than 1.5 mm2.
• The mains connection is fused to a maximum of 16 A.
• Check the rotational direction when connecting to the
power supply or changing location: it may be necessary
to change the polarity (wall socket).
If you have questions always provide the following
information:
• motor manufacturer
• type of current used by motor
• data listed on the machine type plate
If you return the motor always send the complete drive unit
including switch.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Forsa 8.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 8.0 in the language / languages: English, German, Finnish as an attachment in your email.

The manual is 9.46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info