Manual Scheppach DS930 (page 17 of 72) (English, German, Dutch, French, Italian)

781634

Zoom out

Zoom in

1/72

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

17 І 72

Dust extraction

WARNING! Harmfull noxious gases may be generated

when e.g. lead-containing paint is processed. These

gases entail a risk for the operator and the persons in

the vicinity!

Therefore only use the power tool in combination with

a dust extraction unit, and protect yourself and other

persons in the working area with additional suitable

personal protective equipment!

When working with this power tool, a Iot of dust is ge-

nerated. The dust extraction unit is very useful if you

want to keep your workplace clean. lt is possible to

combine the extraction system or a vacuum cleaner

with the extraction hose (8) which is connected to the

adapter for dust extraction.

1. Connect the dust extraction adapter with a suita-

ble dust extraction unit such as a vacuum cleaner

(Fig.6-8).

Note: Make sure that the vacuum cleaner is suitable

for being used tagether with a power tool.

Connection to the power supply

1. Make sure that the power tool is switched off. Al-

ways switch the on/off switch (4) to off position befo-

re connecting the power tool to the power supply.

2. Plug the power plug into a correctly installed socket

which camplies with the requirements specied in

the technical data.

3. Your power tool is now ready for operation.

Operation

Oscillation rate

Before you start working with the swing speed to

match the appliance. Use a low swing speed for coar-

se grinding, increase the oscillation rate for ne work.

1. Rotate the adjustment wheel (6) to adjust the oscil-

lation rate. Turn the wheel clockwise to reduce the

oscillation rate (Fig.9).

2. Turn the wheel counter-clockwise to increase the os-

cillation rate (Fig. 10).

Switching on/off

To switch on:

Push the on/ off switch (4)

Continuous operation: (Fig.11)

Secure the on/off switch (4) with the Ieeking button (A)

To switch off:

Press the on/off switch (4) briey.

Note: The insertion tool moves for a short while after

having it switched off. Do not put aside the power tool

until the insertion tool has come to a complete halt.

Grinding

1. Attach an appropriate abrasive sheet and select the

corresponding speed.

2. Hold the power tool securely at the handle surfaces

(1, 5) and switch it on as described.

3. Wait until the insertion tool has reached its full ope-

rating speed.

4. Apply some pressure to the grinding head (11/12)

such that the insertion tool touches the surface to be

processed.

5. Constantly move the power tool over the surface.

Note: lf you want to avoid irregular grinding results, do

not keep the power tool at one spot for too long.

6. Lift the grinding plate from the surface to be pro-

cessed before switching off the power tool.

especially inhaling them, can represent a hazard

for operating personnel or persons in the vicinity.

Comply with the safety regulations that apply in your

country. Connect the electric power tool to a suitable

extraction system. To protect your health, wear a P2

protective mask.

d) Never use machines with a damaged cable. Do

not touch damaged cables and pull the plug from

the mains power supply if the cable becomes da-

maged during work. Damaged cables increase the

risk of electric shock.

Residual risks

Even if you use this power tool in compliance with

the regulations, there arestill remaining risks. The

following risks may occur due to the type and de-

sign of the power tool:

• Lung damage if no suitable protective dust mask is

used.

• Damage to hearing if no suitable ear protection is

used.

• Health damage caused by hand-arm vibrations if the

equipment is used over a prolonged period or is not

properly guided and maintained.

Tool description (Fig.1)

1. Handle surface

2. LED-Light

3. Adjustment wheel for speed pre-selection

4. On/off switch

5. Main handle

6. Adapter with connecting nut

7. Hoseadapter

8. Extraction hose

9. Triangular velcro sanding plate with extraction

holes

10. Round velcro sanding plate with extraction holes

11. Triangular sanding head

12. Round sanding head

Before start-up

Installation

- Fold the front and back parttagether (Fig.2). And

then tighten the screw nut. (Fig.3).

- The Iongest length installation Insert the additional

handle to the end of the machine. And then turn the

screw nut on the end ofthe machine for tightening.

(Fig.4)

Sandpaper

Selection

1. The grain size of the sandpaper is specied on its

rear side. The smaller the specied number, the

coarser the graining.

2. Use sandpaper with coarse grain for rough grinding,

and sandpaper with ne grain for nishing. We re-

cornrnend sandpapers with aluminium oxide, silicon

carbide or other synthetic abrasives.

3. lf you can chose between sandpapers with different

graining, you should start with coarsegraining sand-

paper and complete the grinding process with the

nest possible graining. Thus you will get good and

smooth grinding results.

How to apply and replace sandpaper

Apply the sandpaper to the grinding plate using the

Velcro strip mechanism.

1. Align the sandpaper with the grinding plate and

press it on evenly.

2. PuII the sandpaper off the grinding plate and replace

it with a new one I another one (Fig.5).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DS930 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DS930 Manual

Product: