781461
25
Zoom out
Zoom in
Previous page
1/148
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
| 25
890
1260
1760
2600
The V-belt must lie in the same groove on the
upper and lower drive pulley.

with an interlock switch (27). The interlocking

gearing covers (21) are closed. The device can-
not be switched on if a gearing cover (21) is not

7. Loosen the locking screw (22) and lower the lever
with the motor unit to tighten the V-belt.
8. Tighten the locking screw (22).
9. Close the gearing covers (21). Secure the gearing
covers with the locking screws (20).
Securing the workpiece
Securing with the 4-prong centre tip (1) and tail-
stock (5) (Fig. 1)
1. Draw a diagonal line at both ends of the work-
piece to locate the centre. The centre is where
the lines meet.   
4-prong centre tip and tailstock are to meet the
workpiece. This ensures a better hold.
2. 
diagonal to enable the 4-prong centre tip (1) to
grip better.
3. -
 
4-prong centre tip (1) into the workpiece with a
 Take
care to protect the thread of the 4-prong centre tip
(1) with a wooden board, for example.
4. -
piece again.
5. Then (re)mount the 4-prong centre tip (1) onto the
device.
      
4-prong centre tip can be found in the chapter

6. Position the workpiece on the 4-prong centre tip
(1). -
gages with the notch, otherwise secure clamping
is not guaranteed.
7. Loosen the lever (8) of the tailstock.
8. Slide the tailstock towards the 4-prong centre tip

to clamp it.
Mounting the face plate
1.  To
do this, place the two open-ended wrenches (16)
on the drive shaft (19) and on the 4-prong centre
tip (1) and unscrew the 4-prong centre tip (1).
2. 
open-ended spanner (16).
3. Screw the face plate (13) onto the drive shaft (19).
10. Operation
Select speed (Fig. 4)
m ATTENTION!
The mains plug shall not be plugged in when ad-
justing the speed.
Select the correct speed:
 -
crease the speed as the weight of the workpiece
increases.
The selection of the correct speed depends on
several factors, e.g. material, diameter, length and
unbalance of the workpiece. 
a low speed for hard timber, non-round, long or
large-diameter workpieces.

The workpiece diameter is indicated on the x-axis.
󰀨 
󰀨

the curve.
1. Loosen the two locking screws (20) on the two
gearing covers (21).
2. Open the gearing covers (21).
3. Loosen the locking screw (22) of the motor unit

4. 
to relieve the load on the V-belt (26).
5.       
screw (22).
6. Place the V-belt (26) in the desired groove of the

25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DM1100T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DM1100T in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 5.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info