781461
24
Zoom out
Zoom in
Previous page
1/148
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
24 |
m ATTENTION!
The device and the packaging material are not
children‘s toys! Do not let children play with
plastic bags, lms or small parts! There is a dan-
ger of choking or su󰀨ocating!
9. Assembly
Assembling the lathe (Fig. 2)
1. Slide the tool support (2) onto the rail with motor
unit (3a).
2. Slide the tailstock (5) to the tool support (2) on
the rail with the motor unit (3a). Check that the
-

3. Connect the rail with the motor unit (3a) and the
rail (3b) without the motor unit together.
4. Screw the two rails together with the three screws
withspring washer and standard washer (17) us-
.
Note:
If it is di󰀩cult to move the tool support (2) or the
tailstock (5), adjust the nut on the underside with
a spanner or ratchet (19 mm).
Setting up the lathe (Fig. 1)
1. 
2. Screw the lathe to the surface. 
in each of the three feet (7) for this.
3. You can use the hexagonal bolts (18) supplied
with the lathe for this.
4. Place the standard washer and spring washer on
the hexagonal bolt (18). 
5. Screw the lathe to the surface with the help of the
hexagonal bolt, standard washer, spring washer
and nut (18).
Fitting/replacing the workpiece mount (Fig. 3)
m ATTENTION!
Switch the device o󰀨 and pull out the mains plug.
Fitting the 4-prong centre tip
1.  To do this,
       
open-ended spanner (16) and unscrew the face
plate (13) from the drive shaft (19).
2. 
open-ended spanner (16).
3. Tighten the 4-prong centre tip (1) onto the drive
shaft using the second open-ended spanner (16).

(13) must be used instead of the 4-prong centre tip
(1).
7. Technical data
 1375 x 325x 415 mm
Speed -1
 1000 mm

diameter 350 mm
Spindle head thread 
 20,5 kg
Engine 
 
Subject to technical changes
* Operating mode S2 – short-term operation
Operation at a constant load for 15 minutes or less,
       
󰀩        
within 2 K of the ambient temperature.
The noise and vibration levels have been determined
in accordance with EN 61029.
Sound pressure level LpA 71
pA 
Sound power level L 84
 
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total
vibration emission values (vector sum of three direc-
tions) determined per EN 61029.
8. Unpacking
-
vice.
       



damage. 
 Later claims will not be
recognised.




time.
-
 -



equipment.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DM1100T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DM1100T in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 5.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info