Manual Scheppach CSE2400 (page 30 of 108) (English, German, Dutch, French, Italian, Polish, Spanish)

781698

Zoom out

Zoom in

1/108

30 GB

Warning! If the extension cable is damaged, pull the

plug out of the power socket immediately. Never work

with a damaged cable.

• Check the chainsaw for damage. Before using your

tool again, check the safety devices or any slightly

damaged parts to ensure that they are in good

working order.

• Make sure the moving parts are working correctly.

• All the parts must be correctly assembled and

meet all the conditions required to ensure that the

chainsaw works correctly.

• Any damaged safety devices and parts must be properly

repaired or replaced immediately by a Customer

Service workshop, unless there are instructions to the

contrary in these operating instructions.

Notes on working practice

Kick-back

You can avoid accidents by not sawing with the tip of

the guide bar as this may cause the saw to rear up

suddenly. Always use the complete safety equipment

and clothes when working with the saw. Kick-back is

an upward and/or backward movement of the guide

bar which can occur if the saw chain at the tip of the

guide bar encounters an obstruction.

Make sure your work-piece is rmly secured.

Use clamps to stop the work-piece slipping. This

also makes it easier to operate the chainsaw with

both hands. Kick-back causes the saw to behave

uncontrollably and thus brings with a slack or blunt

chain. A poorly sharpened chain increases the risk of

kick-back. Never saw above shoulder height.

Operation - tips on chain saw use

Important Notes

• Use the device exclusively for sawing wood.

Do not cut metal, plastics, masonry, building

material that is not made of wood, etc.

• Turn off the engine when the saw comes into

contact with a foreign object. Inspect the saw

and repair it if necessary.

• Protect the chain from dirt and sand. Even a

small amount of dirt will quickly blunt a chain and

increase the risk of kickback.

• Start by cutting a few small logs, using the

exercise to get a feel for your device before you

tackle more difcult tasks.

• Press the casing of the chain saw against the

log when you start sawing.

• Allow the saw to work. Exert only slight

downward pressure.

• In order not to lose control of the device you

should lean towards the end of the incision so

there is no pressure on the saw.

Felling Trees – Only after appropriate training

Caution: Watch for broken or dead branches that

could fall during sawing and cause serious injury. Do

not saw near buildings or electrical wires if you do

not know in which direction the felled tree could fall.

Do not work at night since you will not be able to see

properly, or in rain, snow or storm, as it is difcult to

predict the the direction in which the tree could fall.

• Plan your work in advance.

• The work area around the tree should be clear

so you have a rm foothold.

• The operator should always stand on the uphill

side of the terrain as the tree is expected to roll

or slide after felling.

• Check for broken or dead branches, which can

fall and cause serious injury.

The following conditions may affect the direction in

which a tree falls:

• Wind direction and speed.

• Lean of the tree. The inclination is not always

visible due to uneven or sloping terrain.

Determine the lean of the tree using a solder or

a spirit level.

• Branch growth (and hence weight) on one side

only.

• Surrounding trees and obstacles.

If two or more people are involved in the cutting and

felling, the distance between those who are felling

and cutting should be at least twice the height of the

tree to be felled. When felling trees, make sure that

other people are not put at risk, that supply lines are

not hit and that no material damage is caused. If a

tree comes in contact with a supply line, the supply

company has to be notied immediately.

Look for decay and rot. If the trunk is rotted, it may

suddenly collapse and fall on you. Make sure there

is enough space for the tree to fall safely. Keep

a distance of 2 1/2 tree lengths from the nearest

person or other objects. Engine noise can drown out

a warning call.

Remove dirt, stones, loose bark, nails, staples, and

wire from the tree where you are going to cut.

Keep an escape route (Fig. A)

Before felling, an escape route has to be planned

and cleared, if necessary. The escape route should

lead diagonally away from the back of the falling tree

(Fig. A).

Item 1: Plan of emergency exits

Item 2: Position in which the tree falls

Felling of large trees - only with appropriate

training

(15 cm in diameter)

Fell large trees using the notch method. Here, a

wedge is laterally cut out of the tree according to the

desired direction of fall. After a cut has been made

on the case of the other side of the tree, the tree will

fall in the direction of the wedge.

m Note: If the tree has large prop roots, they should

be removed before making the notch. If the saw is

used to remove the prop roots, the chain should

not touch the ground, to prevent it from becoming

become blunt.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2400 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CSE2400 Manual

Product: