Manual Scheppach CSE2400 (page 28 of 108) (English, German, Dutch, French, Italian, Polish, Spanish)

781698

Zoom out

Zoom in

1/108

28 GB

• The specied vibration emission value can also be

used for an initial assessment of the load.

Warning:

• The vibration emission value can vary from the

specied value during the actual use of the electric

tool, depending on the type and the manner in

which the electric tool is used;

• Try to minimise stress from vibrations as low as

possible. Some examples of means for reducing

the vibration stress are wearing gloves while using

the tool and limiting work time. In the process all

parts of the operating cycle must be taken into

account (such as times in which the electric tool is

switched off or time in which it is switched on, but is

not running under a load).

7. Attachment and operation

Warning!

Always wear safety goggles, ear muffs,

protective gloves and heavy-duty work clothes!

Use the saw only with approved extension cables with

the prescribed insulation and connections designed

for outdoor use (approved rubber-sheathed cables)

which t the chainsaw plug.

The chain saw is equipped with safety switches,

requiring the use of both hand. The chainsaw works

only when one hand is pushing the button 11 and 13

at the same time. If the chainsaw does not run, the

chain brake must be released at the front nger guard

(3). Be

sure to read the sections “Chain brake” and “

Releasing the chain brake “ on this point.

To switch on:

• Release the chain brake (3), push in the lock (11)

and press the power switch (13).

• Place the lowest claw (Fig 2, J) on the wood . Raise

the chain saw by the rear grip (1 ) and saw into the

wood. Move the chain saw back a little and place

the claw further down.

• Be careful when sawing splintered wood as pieces

of wood may be ripped off.

After switching on, the chainsaw will run immediately

at high speed .

To switch off

• Release either the ON/OFF switch (13) on the rear

grip.

• The release of ON/OFF switch results the stop of

the chainsaw within 1sec., and heavy sparkling.

This is normal and safe for the proper operation of

the chainsaw.

• After working with the chainsaw, you should always:

Clean the saw chain and guide bar and replace the

chain guard.

• If the chain brake is activated the chainsam will be

deactivated immediately.

8. Initial operation

The voltage and current supply must comply with the

ratings on the type plate.

Before commencing work, always check that the

chainsaw works properly and is safe to operate.

Check also that the chain lubrication and the oil

gauge are in good working order (see Fig.4). When

the oil lever is approx. 5 mm from the bottom mark,

you must top up with oil. When the oil level is higher

you can work without worry.

• Switch on the chain saw and hold it above the

ground. Be careful not allow the chainsaw to touch

the ground. For safety reasons it is best to keep

a clearance of at least 20 cm. If you now see

growing traces of oil, the chain lubrication system

is working correctly. If there are no traces of oil at

all, try cleaning the oil outlet (Fig 2, C), the upper

chain tensioning borehole (Fig 3, e) and the oil

duct, or contact your Customer Service. (Be sure

to read the section “Filling in chain oil and chain

lubrication” on this point).

• Check the chain tension and retention, if necessary (see

the section “Tensioning the saw chain” on this point).

• Make sure the chain brake is working properly (see

also the section “Releasing the chain brake”).

Assembly

Fitting the guide bar and chain (Fig 1, 2, 3)

Warning! If the chain saw is already connected to the power

supply: Pull the plug from the socket outlet. Wear protective

gloves whenever doing any work on the saw chain.

Important: The front nger guard (3) must always be

in the top (vertical) position (Fig. 5).

The guide bar and saw chain are supplied separately.

To assemble, rst unscrew the lock nut (SDS-

system/5) and remove the guide bar cover (6). The

guide bolt (17) must be in the centre of the guide.

If necessary, adjust the chain tensioning with the

chain wheel (Fig.3, 5a).

Warning! To prevent injury on the sharp cutting

edges, always wear gloves when assembling,

tensioning and checking the chain.

Before assembling the guide bar with the saw chain,

check the cutting direction of the teeth!

The running direction is marked with an arrow on the

cover (6). To determine the direction of cut, it may be

necessary to turn over the saw chain (4).

Hold the guide bar (7) vertically with the tip pointing

upwards and put on the saw chain (4, beginning at

the tip of the bar.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2400 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CSE2400 Manual

Product: