781698

Scheppach CSE2400 Manual

32
Zoom out
Zoom in
Previous page
1/108
Next page
32 GB
• Keep the cooling vents on the motor housing clean
and unobstructed at all times.
• Only the maintenance work described in these
operating instructions may be carried out. Any
other maintenance work must be carried out by our
Customer Service.
• Do not modify the power saw in any way as this
could jeopardize its safety.
• Should the chainsaw fail despite our careful
manufacturing and inspection procedures, have it
repaired by an authorized Customer Service work-shop.
Filling in chain oil
To prevent dirt getting inside the tank, clean the oil
tank cap (21) before opening. Check the contents of
the oil tank during sawing work by checking the oil
gauge (15). Close the oil tank cap tightly and wipe
away any spills.
Sharpening the saw chain
You can have your saw chain sharpened fast and
correctly by specialist dealers, from whom you can
also obtain chain sharpening equipment to enable
you to sharpen the chain yourself.
Please follow the corresponding operating
instructions.
Take care of your tools. Keep your tools sharp and
clean to enable you to work well and safely.
Follow the maintenance regulations and the
instructions for changing tools
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use as
consumables. Wear parts*:
• saw chain
• guide bar
• chain oil
• carbon brushes
• claw stop
* Not necessarily included in the scope of delivery!
11. Storage
• Before every transport and storage, attach the
chain guard.
• Store the device in a dry place beyond the reach
of children.
• When the device is not being used, store it so it
cannot be started by unauthorised persons.
Warning!
Do not store the device without protection outside or
in a damp environment.
12. Electrical Connection
The installed electric motor is connected and is ready
to work.
• Watch out for spring backs. Use extreme caution
when cutting small size limbs. Pliable material
may catch in the saw chain and be whipped
toward you or pull you off balance.
• Watch out for spring backs. This is especially
true for branches that are bent or under pressure.
Avoid coming in contact with the branch or the
saw when there is tension in the wood.
• Keep your work area clear. Keep the path clear
of branches to avoid tripping over them.
Lopping (Fig.J)
• Lopping means removing branches from the
felled tree.
• Leave the larger limbs that are underneath the
felled tree, and use them as support while you
continue to work.
• Start at the base of the felled tree and work your
way up to the top. Remove smaller parts of the
tree with a cut in the direction of growth (arrows
Fig. J).
• Be sure to keep the tree between you and the saw.
• Remove larger, supporting branches using
the methods in the section „Bucking without
restraints“.
• Always cut branches under tension from the
underneath to the top, so the saw does not
become trapped.
• Always cut small and freely hanging limbs with
one cut. By undercutting they could fall in and
pinch the saw.
Trimming (Fig. I)
Attention: Leave stubs in branches or below cut
them to shoulder level only. Never cut branches
above shoulder height. Leave such work to an expert.
• Make the rst cut (Item 1) 1/3 in the bottom of
the limb.
• Then cut the second section (Item 2) all the way
through the branch. The third section (item 3) is
a general section that allows you to separate the
branch at 2.5 to 5 cm from the trunk.
Sawing on a slope (Fig. K)
When sawing on a slope, make sure you always
stand higher than the tree trunk (Fig. K). In order to
maintain complete control at the moment of “sawing
through”, reduce pressure towards the end of the
cut without releasing your tight grip on the handles
of the chainsaw.
Warning!: The saw chain must not come in contact
with the ground..
After completing the cut, wait for the saw chain to
come to a standstill before removing the chainsaw.
Always turn off the chainsaw’s motor when going
from one tree to the next.
10. Maintenance
Always pull the plug out of the power socket before
doing any work on the chainsaw!
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CSE2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2400 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info