782516

Scheppach CJS25-20Li Manual

22
Zoom out
Zoom in
Previous page
1/80
Next page
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
22 | GB
10. Installation
m IMPORTANT!
You must fully assemble the appliance before
using it for the rst time!
Note: Use a suitable coolant, e.g. cutting oil. This im-
proves the endurance and increases the service life
of the metal saw blade.
Saw blades are available which have been optimal-
ly designed for particular tasks. You can use any of
these saw blades provided they have the correct
shank tting (single lug shank).
Mounting / replacing saw blades
Warning ! Pull the mains plug out of the socket be-
fore you carry out any task on the device, otherwise
there may be risk of injury.
• Turn the quick-release chuck (18) and hold it in the
turned position.
• Press the selected saw blade (14) up to the stop in
the quick-release chuck (18). The saw blade (14)
should then engage.
• The saw blade (14) must lie in the guide roller (13).
• Release the quick-release chuck (18). The chuck-
must then return to its original position. The saw
blade (14) is then locked in place.
Attaching the guide fence
The guide fence (19) can be attached on the left or
right side of the device (see g. A).
• Release the two locking screws of the fence guide
openings (15).
• Slide the guide fence (19) into the fence guide
openings (15).
• Re-tighten the two locking screws.
Operation
Setting the cutting angle
• Release the clamp screw (11) using the Allen key
(20).
• Set the cutting angle 0° / 15° / 30° / 45° (left / right)
on the base plate (9). The embossed marking for
each recessed line indicates the cutting angle set-
ting. The housing has a stop pin (21) (see g. B)
which must engage in the appropriate recessed
line.
• Tighten the clamp screw (11) using the Allen key
(20).
the battery cells.
13. Never leave batteries to charge unsupervised!
Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions“ and the „Proper use“ are observed
along with the whole of the operating instructions.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet. Use the tool that is recommend-
ed in this manual.. This ensures that your machine
performs optimally.
• Hands may never enter the processing zone when
the machine is in operation.
9. Intended use
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment’s potential hazards.
It is also imperative to observe the accident preven-
tion regulations in force in your area.
The same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
The machine may be used only with original acces-
sories and original tools of the manufacturer.
The safety-, workplace- and maintenance specica-
tions of the manufacturer as well as the dimensions
specied in the technical data must be observed.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CJS25-20Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CJS25-20Li in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info