782495
18
Zoom out
Zoom in
Previous page
1/122
Next page
16 english
19 slant scale
20 intake slit
21 carrying handle
Assembly
Warning: For your own safety, connect the machine to the
power source only after all of the of the steps to assemble
the machine have been completed and you have read and
understood the operating instructions with all of their safety
and operating notes.
Note: Organize all of the parts that you need for the assem-
bly before you begin. Note the assembly instructions and
follow them carefully with the help of a second person.
Freeing the Intake Slit (fig. 2)
After the saw has been removed from the package, release
the blocking knob of the intake slit (1). When the mitre box
saw is being transported or stored the intake slits must al-
ways be blocked. The slit block knob (1) is on the right side
of the slit.
Assembling the Hand Grip (fig. 1)
Thehandgrip(9)onthefrontsidemustbeturneduntil
it is tight.
Assembly of the Dusk Bag (fig 4)
• Inordertoinstallthedustbag(1),pressthemetalcollar
wings(2)together.
• Placethecollaropeningofthedustbagonthedustsup-
ports(3)andreleasethemetalcollarwings.
Assembly of the Screw Vice (fig. 5)
• Placeaknuriedscrew(1)onthebackofthemachine
body, one for each side.
• Placethescrewvice(2)intheprepareddrillholeson
the body.
Saw Blade Key (fig. 6)
Forpracticalstorageandtopreventlossofthekey,thereis
aclipforitontherightsideoftheintakeslit.
Note: We strongly recommend that this crown and mitre
boxsawbe ttedsecurelyonaworkbench, sothatyour
machineisasstableaspossible.
• Findandmarkthefourplacesontheworkbenchwhere
holes are to be drilled.
• Drilltheholesintothebenchwitha¿10mmbit.
• Screwthecrownandmitreboxsawwithscrews,wash-
ers and nuts securely onto the bench. Please be aware
thatthesefasteningelementsarenotsuppliedwiththe
machine.
Start Up
Note: This machine was precisely adjusted before leaving
the factory. Check the precision and adjust it if necessary
in order to achieve the best operating results (see also the
section on corrective measures).
Tool operation
WARNING! Never connect the machine to a power source
before all installation and positioning has been completed
and you have read and understood the safety and operating
instructions.
Basic Operation of the Crown and Mitre Box Saw with Intake
Function
• Always use a screw vice to hold the materials tightly.
There are two holes on the machine to secure the screw
vice(g.5).
• Alwayspositionthematerialsonthesurfacearea.Any
twisted or crooked materials which cannot lie flat on the
table or the surface area can get caught in the saw blade
and should not be used.
• Neverputyourhandsintheareaofthesaw.Keepyour
handsatalltimesoutsideofthe„ForbiddenHandArea,“
which includes the entire mounting table. This area has
a„NoHands“sign.
Warning: In order to avoid accidents resulting from materi-
alsthatyoutofthemachine,theplugmustbetakenout
ofthesocketandthenthesmallpiecesremoved.
Tounlockthesawheadwhenitisinatiltedposition:
• Pushthesawhead(1)andtheblockinglever(4)gently
downward.
• Pulloutthespringchock(2).
• Bringthesawheadintothefullyuprightposition.
Switching on the Saw (fig. 15)
Pushthesafetygrip(1)downwardandpushtheswitch(2)
to switch on the saw.
Straight Cut (g. 16)
• Tomakeastraightcutinasmallpieceofmaterial,push
thecompletesawheaddownandpullopentheslitblock
grip(1).
• Tosawthickerboards(upto305mm),theslitblockgrip
must be released so that the saw head can move freely.
• Placethematerialstobecutonthetable,ushagainst
the chock. Use the screw vice that is attached to the
bodyofthemachinewheneverpossible.
• Pushthe safetylever(5) downwardand press theon/
offswitch(3)toswitchonthesaw.Movethebladeby
meansofpressingthegrip(4)downwardintothemate-
rialwithaslowandsteadypressure.
• Whenthecutiscomplete,presstheswitchandletthe
saw blade come to a full stop before raising the saw
head.
Bevelled Cuts (fig. 17)
Thismachineisequippedwithtenbevellingsprings(1)on
thebody.Theyareplacedat0,15,22.5,31.6and45de-
grees to the left and right as well as 60 degrees to the left.
Thesesettingscorrespondtothemostoftenusedbevelled
cuts. Here is how you make a bevelled cut:
• Release the bevelled montage table by lifting up the
quickrelease(2).
• Asyouraisethespringgrip(3),grabthehandgrip(4)
and turn the montage table to the left or right to the
desired angle.
• Lockthespringgripintothedesiredangle.
Note: The lever can only be locked into one of the ten
lockingpositions.
• Once the desired bevelling angle has been reached,
pressthebevelmontagetabledowninordertoxthe
position.
• Shouldthedesiredbevellinganglenotbeoneoftheten
presets,simplyadjustthetabletothedesiredangleby
pushingthebevellingmontagetable(2)releasedown.
Slanted Cuts (fig. 18, 19)
Warning: Inordertoproduceslantedcutsthebladeposi-
tion must be fully brought to the left or right. Otherwise
there is not enough room for the saw blade to be carried all
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Capas 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Capas 5 in the language / languages: All languages as an attachment in your email.

The manual is 9.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info