782495
20
Zoom out
Zoom in
Previous page
1/122
Next page
18 english
Danger: The laser is activated when the saw blade turns.
Donotlookintothebeam,evenwithopticalinstruments.
Do not remove the warning sign which is attached to the
saw blade cover. Avoid direct eye contact with the light
source.
Note: Theredlaserbeamappearsasadottedlinewhen
the motor is activated and the saw blade Is in the highest
position.Thisdottedlineallowsyoutoadjustthemarkings
on the materials with the cutting line of the saw blade.
Whenthesawbladeisbroughtdownward,theprotection
is removed and the dotted line becomes a continuous laser
beam.
LaserWarningSign:Maximumoutput<1mWDiodenlaser:
630–670nm.CorrespondstothestandardEN608251.
Laser Operation
Withthesawbladeunitinthemostuprightposition:
• Placeyourmaterialsonthemitreboxsaw.
• Switchthesawontoactivatethelaserbeam.
• Makesurethatthelaserbeamandthemarkingsonyour
materialsareinagreement.(Warning: do not lower the
sawbladeduringadjustments.)
• Should the markings on the materials and the laser
beam not agree with each other, switch the machine off,
waituntilthebladehascometoacompletestandstill,
andadjustthepositionofthematerials.
• Switchthesawonandrechecktheline.
• Onceagreementhasbeenreached,fastenthematerials
with a screw vice and carry out the cut.
Changing the Saw Blade (fig. 24, 25, 26)
Warning: In order to prevent an unintentional start up of
the saw, always switch off and unplug the machine be-
fore changing the saw blade. Use correctly sharpened saw
blades. Conform to the maximum speed and the tooth type
indicated on the saw blade. Exchange of saw blades and in-
stallation must be carried out correctly. Only use saw blades
of the type recommended in the operating instructions.
Removal of the Saw Blades
• Unplugthemachinefromthepowersource.
• Raisethemitreboxsawintotheuprightposition.
• Raisethelower,transparent,plasticsawbladecoverinto
themostuprightposition(1,g.24).
• Whileholding onto thelower sawbladecover, release
thescrewofthecover(2,g.24)withaPhillipsscrew-
driver.
• Turnthecover(3)soastorevealtheframescrew(4,
g.26).
• Putthebladekeyontheframescrew.
• Findthecorrugatedclosureandholdthissteadywhile
turning the blade in a clockwise direction. The corrugat-
edclosurewillclickinandadjusttheguard.Continue
to hold the closure while turning the key in a clockwise
direction to release the closure.
• Removethebracingclamp(5,g.26)fromthebracing
cylinder(6)andtheblade(7).Donotremovetheinner
cylinder.
• Liftupthetransparent,plasticsawbladeprotection(1,
g.24)totheuprightpositioninordertoremove the
blade.
Note: Pay closeattentionto thepartswhichyouremove
andthewaytheywereinstalled.Cleananysawdustaway
fromthecylindersbeforeyouinstallanewblade.The254
mmbladehasawaveholewitha16mmreductionpiece
in order to assemble it on the saw.
Installing the Saw Blade
Unplug the machine before changing or installing a saw
blade.
• Installa254mmsawbladewitha16mmwave.Please
notethatthedirectionalarrowwhichpointsinaclock-
wise direction and the upper saw blade must be in
agreementontheblademustcorrespondtoeachother
andthesawbladeteethhavetopointdown.
• Putthebracingcylinder(4,g.26)ontothebladeand
thewave.Screwthebracingcylinder(6)tothewavein
an anticlockwise direction. Important: Make sure that
theatpartofthecylinderandtheatpartofthewave
shaftlockintoeachother.Equally,theatsideofthe
bracing cylinder must meet the blade.
• Placethebladekeyintothewavescrew.
• Pressonthewaveclosure(5,g.25)andholdittightly
while turning the blade in an anticlockwise direction.
Whenitclicksin,pressthewaveclosurefurtherdown
and turn the bracing screw until it is tight.
• Returnthecoveringplates(3,g.24)totheiroriginal
positionuntiltheslitinthecoverisoverthescrew(2,
g.24). While holding on to the lower saw blade lid,
tightenthescrewwithaPhillipsscrewdriver.
Note: Thelower sawblade covermust bein theupright
positioninordertoachieveaccesstothecoveringplate
screw.
• Movethetransparentsawbladeprotectioncover(1,g.
24)downandmakesurethatnowheredoesItmakecon-
tact with the blade.
• Seethatthewaveclosureisreleasedsothattheblade
can turn freely. Turn the blade until the closure is re-
leased.
Note: Bothcylinderpartsmustbecleanandproperlyposi-
tioned. Put the blade down into the lower table and ensure,
by turning it by hand, that it does not come into contact
with the body of the machine or the mounting table.
m Electrical Connections
• Checktheelectricalconnections.Donotusedamaged
cables. See the section on electric cables.
• Onlyanelectricalspecialistshouldundertakeinstalla-
tion,repairsandmaintenanceworkontheelectriccon-
nections.
• To deal with power malfunctions, switch off the ma-
chine.Pullouttheplug.
• Switchoffthemotorwhenyouleavetheworkplace.Pull
outtheplug.
• Even when the machine is only being moved a small
distance,unplugitfromexternalpowersources!Before
operatingthemachineagain,plugthemachineinprop-
erly!
Theelectricmotorinstalledinthemachineisreadytoop-
eratewhenitisdelivered.Theconnectioncorrespondsto
therelevantVDEandDINnorms.Thecustomer‘selectri-
cal connection as well as the extension leads used must
alsocorrespondtothesenormsor,respectively,thelocal
electrical standards.
Defective Electrical Connections
Electricalconnectionscanoftenhaveinsulationdecien-
cies. Possible causes include:
• Pressurepointswhenthecableispassedthroughdoor
or window cracks.
• Bendingpointsduetoinexpertbindingorlayingofelec-
trical cables.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Capas 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Capas 5 in the language / languages: All languages as an attachment in your email.

The manual is 9.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info