782181

Scheppach BS500 Manual

13
Zoom out
Zoom in
Previous page
1/39
Next page
14 english
Malfunction Possible cause Solution
1.
Brake motor has no brake function
a)
Brake pads are worn
Have brake pads renewed.
Electrical connection works only by a
specialized electronics technician!
2.
Saw blade detaches after switching off the
motor.
a)
Attachment nuts are not tightened enough
b)
Brake effect of motor is too strong
a)
Tighten attachment nuts M20 left-hand
thread
b)
Adjust electric current brakes
•
Take out little plug sideways from switch
housing
•
Use small screw driver to adjust carefully
the electric current of the brakes on the
potentiometer
•
After switching off the motor the saw blade
stagnation should take place after 8 - 19
seconds
•
Put the little plug into the switch housing
again
3.
Motor does not initiate
a)
Breakdown mains fuse
b) Extension cable defect
c)
Connections to the motor or to the switch
are not in order
d)
Motor or switch is defect
t
a)
Check mains fuse
b)
See instructions “Electrical connections“
c)
Have it checked by an electronics
technician
d)
See instructions “Electrical connections“
4.
Motor runs backwards or forwards
Condensator defect Have it exchanged by an electronics
technician
5.
Motor does not perform, switches off
automatically
Overcharged because of
a)
Blunt saw blade
b) 2 Phase run – Motor becomes hot
a)
Put in a sharpened saw blade
b)
Have the extension cable and the main
power supply checked by a specialized
electronics technician
6.
Burn marks on the intersection
by longitudinal cuts
by cross cuts
a)
Blunt saw blade
b)
Wrong saw blade
c)
Longitudinal end stop not parallel to saw
blade
d)
Slide table not parallel to saw blade
a)
Put in a sharpened saw blade
b)
Put in a saw blade for longitudinal cuts
c)
Re-adjust motor on rocker or exchange
longitudinal end stop
d)
Align slide table to saw blade
7.
Wrong rolling direction by rotary current
motor
Socket wrongly tapped Change polarity of socket
TROUBLESHOOTING PLAN
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BS500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS500 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info