Manual Scheppach BGS700 (page 18 of 136) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

781662

Zoom out

Zoom in

1/136

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

ses not intended.

8. Dress properly

Do not wear loose clothing or jewellery.

They can be caught in moving parts. Rubber

gloves and non-skid footwear are recom-

mended when working outdoors. Wear

protective hair covering to contain long hair.

9. Use safety glasses

Also use face or dust mask if cutting operati-

on is dusty.

10. Don’t abuse cord

Never carry tool by cord or yank it to disconnect

it from receptacle. Keep cord from heat, oil and

sharp edges.

11. Secure work

Use clamps or a vice to hold work. It’s safer

than using your hand and it frees both hands

to operate tool.

12. Don’t overreach

Keep proper footing and balance at all times.

13. Maintain tools with care

Keep tools sharp and clean for better and

safer performance. Follow instructions for lu-

bricating and changing accessories. Inspect

tool cords periodically and, if damaged,

have repaired by authorized service facility.

Inspect extension cords periodically and

replace if damaged. Keep handles dry, clean

and free from oil and grease.

14. Disconnect tools

When not in use, before servicing, and when

changing accessories.

15. Remove adjusting keys and wrenches

Form the habit of checking to see that keys

and adjusting wrenches are removed from

tool before turning it on.

16. Avoid unintentional starting

Don’t carry plugged-in tool with nger on

switch. Be sure switch is off when plugging

in.

17. Outdoor use extension cords

When tool is used outdoors, use only exten-

sion cords intended for use outdoors and so

marked.

18. Stay alert

Watch what you are doing. Use common

sense. Do not operate tool when you are

tired.

19. Check damaged parts

Before further use of the tool, a guard or

other part that is damaged should be care-

fully checked to determine that it will operate

properly and perform its intended function.

Check for alignment of moving parts, binding

of moving parts, breakage of parts, moun-

ting, and any other conditions that may

affect its operation. A guard or other part that

is damaged should be properly repaired or

replaced by an authorized service-center

unless otherwise indicated elsewhere in

this instructions manual. Have defective

switches replaced by an authorized service-

center. Do not use tool if switch does not

• Catapulting parts out of damaged grinding

wheels.

• Catapulting of workpieces and parts of workpi-

eces.

• Damage to hearing if essential ear-muffs are not

used.

• Harmful emissions of wood dust when used in

closed rooms.

• The rotating parts of the device cannot be cov-

ered for functional reasons. Therefore you must

exercise care and hold the workpiece rmly to

prevent it slipping which could result in your

hands coming into contact with the grinding/

sanding belt.

The equipment is allowed to be used only for its

prescribed purpose. Any other use is deemed to

be a case of misuse. The user/operator and not the

manufacturer will be liable for any damage or injuries

of any kind resulting from such misuse.

Please note that our equipment has not been desig-

ned for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the equipment

is used in commercial, trade or industrial businesses

or for equivalent purposes.

5. Safety information

m Caution!

Read all safety regulations and instructions. Any

errors made in following the safety regulations and

instructions may result in an electric shock, re and/

or serious injury. Keep all safety regulations and

instructions in a safe place for future use.

m Warning! To protect against electric shock, injury

and re the following basic safety precautions must

be observed when using power tools.

Read and follow these instructions before using the

equipment and keep the safety information in a safe

place.

1. Keep work area clean

Cluttered areas and benches invite injuries.

2. Consider work area environment

Don’t expose power tools to rain. Don’t use

power tools in damp or wet locations. Keep

work area well lit. Don’t use power tools in

presence of ammable liquids or gases.

3. Guard against electric shock

Prevent body contact with grounded surfaces

(e.g. pipes, radiators, ranges refrigerators).

4. Keep children away

Do not allow other persons to touch the

equipment or cable, keep them away from

your work area.

5. Store idle tools

When not is use, tools should be stored in dry,

high, or locked-up place, out of the reach of

children.

6. Don’t force tool

It will do the job better and safer at the rate for

which it was intended.

7. Use right tool

Don’t force small tools or attachments to do the

job of heavy duty tool. Don’t use tools for purpo-

18 / 136

FR CZ SK DK ES FIN IT NL PL PT SE SI NO

GBDE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BGS700 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6.01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BGS700 Manual

Product: